Frigidaire Range Control Board 316462841 — Fix Oven That Won't Heat, Display Errors, or Unresponsive Controls

OEM REPLACEMENT PART Frigidaire Range Control Board 316462841 Part# 316462841 Fits Frigidaire Fits Electrolux Electric Range / Oven Frigidaire Range Oven Not Heating, Showing Error Codes, or Controls Unresponsive? Control Board 316462841 – Fix It Fast An oven that won't heat, displays persistent error codes, or has completely unresponsive touchpad controls almost always has a failed range control board. In most Frigidaire and Electrolux electric ranges, the control board is the central brain that manages oven temperature, bake and broil elements, the clock, and all touchpad inputs. When it fails, the oven may refuse to heat, display F-codes that won't clear, lock up entirely, or behave erratically — even though the range top burners may still work. ⚡ One of the most common electronic failures in Frigidaire-built electric ranges. Part 316462841 is the genuine OEM replacement control board that restores full oven operation, clears persistent error codes, and returns all controls to normal function. ❓ Is This the Right Part? This is the correct fix if ALL of the following are true: ✔ Range has power — clock or display shows something (even an error code) ✔ Surface burners work normally (rules out a power supply issue) ✔ Bake and broil elements have been tested and confirmed not open/burned out ✔ ONLY problem is the oven not heating, persistent F-codes that won't clear after a power reset, or a completely unresponsive or erratic touchpad Not sure? Send us your model number — we'll confirm before you order. 🔧 Common Symptoms Oven does not heat on bake or broil despite elements testing OK Persistent F-code error (F10, F11, F30, F31, etc.) that returns after power reset Touchpad controls completely unresponsive or randomly activating Oven overheats or runs continuously without shutting off Display blank, flickering, or showing garbled characters Oven door locks unexpectedly and won't release ✔ If these symptoms match, this is the most likely failed component in the system. ✔ In most cases, replacing this control board restores full oven operation and clears all error codes immediately. 📦 Part Details Part Number: 316462841 Type: Electric Range Oven Control Board (ERC / Electronic Range Control) Brands: Frigidaire, Electrolux OEM: Genuine Frigidaire replacement part Also available: Certified pre-owned / used option available on this listing ⚠️ Recommended While Repairing: Before replacing the control board, test the oven temperature sensor (RTD probe). A shorted or open temperature sensor causes F10/F30 error codes that mimic a failed board — and a new board installed with a bad sensor will fail again quickly. The sensor is inexpensive and easy to test with a multimeter (should read ~1080Ω at room temperature). Replace it at the same time if it's out of spec. ⚙️ Installation Skill Level: Moderate — 30–45 minutes. Disconnect power at the breaker before servicing. Access the control board by removing the back panel or console depending on your model, disconnect all wire harness connectors (photograph before disconnecting), transfer any mounting hardware to the new board, reconnect all harnesses, and reassemble. Restore power and run a bake cycle to confirm normal operation and verify no error codes return. ✓ Compatible Models Confirmed compatible with select Frigidaire and Electrolux electric range models. Contact us to verify your model number before ordering. 💡 Pro Tip Always Test the Temperature Sensor Before Ordering a Board: The single most common misdiagnosis on Frigidaire ranges is replacing the control board when the real culprit is the oven temperature sensor (RTD probe). A shorted sensor causes a runaway F10 error that looks exactly like a board failure. Test the sensor with a multimeter — it should read approximately 1080Ω at room temperature. If it reads open, shorted, or wildly out of range, replace the sensor first. It costs a fraction of the board and takes 10 minutes to swap.