INVID-DDPB3: AC Surveillance Power Enclosure

AC Surveillance Power Enclosure with Automatic Source Switching and Remote Monitoring The Defender Box DDPB3 is a rugged, weatherproof surveillance power platform built to keep cameras running where reliable power doesn’t exist. It pairs a Victron solar charging system with a high-capacity lithium battery and AC input, automatically switching between solar and grid power to maintain continuous uptime — on sunny days, cloudy stretches, or sites with no utility connection at all. Running entirely on solar and battery, the DDPB3 keeps a full PTZ-and-turret camera load online for days at a time; connect AC and there’s no power ceiling. Integrated Victron monitoring lets teams check system health, diagnose issues, and even power-cycle cameras remotely — cutting truck rolls and keeping deployments live. Engineered for construction sites, parking lots, perimeters, and remote commercial areas, the DDPB3 delivers a clean, self-sufficient platform for powering and protecting critical surveillance equipment far from traditional infrastructure. Features Hybrid solar-and-AC power system with automatic source switching — maintains uptime on solar, grid, or battery with no manual intervention Victron solar charging system (SmartSolar MPPT 100/20 controller, Cerbo GX hub, and SmartShunt battery monitor) for efficient, regulated charging Integrated AC & Solar Control Module (ASCM) accepting 110–277VAC for direct battery charging, with AC-fail alarm output High-capacity 24V 114Ah ternary lithium battery (~2,530Wh) with integrated heater and CANBUS communication, on a pull-out tray for easy service Extended off-grid runtime — up to 4 days at 25W on solar and battery, supporting one PTZ and two turret cameras on solar alone; no camera-count limit when running on AC Multi-voltage DC output for flexible device support: 12V EPS, dual 12V, 24V, and 48V rails, plus IO-controlled load output Solar input supporting client-supplied panels up to 580W Full remote visibility of system status through the integrated Victron monitoring platform (Cerbo GX + SmartShunt) Remote management — monitor operating status, troubleshoot, and turn cameras on/off remotely to reduce site visits Active thermal management with two UL-listed temperature-controlled fans and a cold-weather battery heater for reliable operation across climates Weatherproof AC power entry with IP68-rated stainless steel connector and UL-listed waterproof male/female connectors Flexible cable entry including 3/4” NPT knockout and cap, PG16 connectors, and clean cable-in routing Pre-installed mounting positions for 4G antennas and horn speakers to streamline wireless and deterrence installs Three pre-made camera mounting plates for fast, consistent camera installation Expandable interior — fourth/fifth-layer space with a detachable platform for routers, PoE switches, and additional edge devices Multiple mounting options including pole and wall brackets with PTZ support, fitting pole diameters from 3.5” to 9.8” (9–25 cm) Durable aluminum-and-stainless construction with integrated hand carrier for portable, installer-friendly deployment Spec Model INVID-DDPB3 Pre-installed Electric system Ternary lithium battery 24V/114Ah,total 2530.8Wh(Battery own capacity) Running time: 3.7 days for 25W(DOD 80%) Installed at the first layer of box ,pull-out design Solar system With sockets for battery input , solar input,mppt pv input,mppt batt input,load connection AC system With USA standard quick connector for AC power AC(110V-277V) power can directly charge battery With IO AC fail alarm out Load system With 1 *12VEPS output. Rate current 2A, Max current 3A With 2 *DC12V output. Rate current 7A, Max current 8A With 1 *DC24V output. Rate current 3A, Max current 4A With 1 *DC48V output. Rate current 5A, Max current 7A With 1 *IO load for remotely turn on and off for load output Victron solar equipment 100/20 MPPT+ Cerbo GX+ SmartShunt The solar panel is client-supplied by default, with a maximum supported power of 580W Fourth and Fifth Layer of Box Spec. Space for devices like router and poe switch The platform is detachable Note: 4G router need connects to 12V EPS Enclosure Pre-installed air ventilation With Air supply and exhaust hole With 2 temperature controlled fan (12 V) Pre-installed holder or hole For antenna and speaker Pre-installed mounting plates For cameras. 3 *pre-made camera mounting plate Material Aluminum and stainless steel combined Mount Pole & Wall (9-25CM diameter pole is perfect) Dimension (W x H x D) 18.9 x 21.3 x 13.4 in (480x540x340mm) (Including Mount) Weight 88.6 lbs (40.2kg) (with battery Included) 46.3 lbs (21kg) without battery (including package box and accessory bag) Ordering INVID-DDPB3: Enclosure Box Downloads Spec Sheet