180° Double Bullhorn Light Pole Bracket for 3" Round Pole – Dual 2-3/8" Slip Fitter Tenon, Heavy-Duty Steel

COMMERCIAL LIGHT POLE ACCESSORY180° Double Bullhorn Light Pole Bracket Dual 2-3/8" Slip-Fitter Tenons for Compatible 3" Round Poles Mount two compatible outdoor lighting fixtures on one pole with this heavy-duty welded-steel 180° double bullhorn bracket. The opposing arms create two fixture positions for parking lots, streets, warehouses and commercial properties. The center mount has an approximately 3.2" inside diameter / 3.5" outside diameter and is designed for a compatible 3" round pole. Each arm provides a 2-3/8" OD tenon for compatible slip-fitter fixtures. 180° Dual Mount3" Round Pole2-3/8" TenonsWelded SteelBlack Finish 180°Opposing Mounts 3"Round Pole 2-3/8"Tenon OD 2 LightsPositions SteelConstruction BlackFinish Check Pole & Fixture Compatibility 3.2" IDCenter sleeve 3.5" ODCenter sleeve 3" PoleDesigned size 2-3/8" ODEach tenon Important: Measure the actual outside diameter of your pole and verify the slip-fitter opening on each fixture before ordering. Nominal sizes can vary. Mount Two Lights on One Pole A double bullhorn bracket lets one compatible pole support two fixtures facing opposite directions. 01180° Configuration Two opposing arms create two light positions.022-3/8" Tenons Each arm accepts compatible slip-fitter fixtures.03Single Pole Connection The center sleeve mounts over a compatible 3-inch round pole. Heavy-Duty Welded Steel Construction Built from welded steel tubing for a rigid commercial lighting mount with a black exterior finish. Welded SteelRigid structure 20"Approx. length 3.5"Approx. width 7.1"Approx. height Compatible Outdoor Light Types Use with fixtures that have a compatible 2-3/8" slip-fitter mount. LED Shoebox LightsParking Lot LightsArea LightsStreet LightsFlood LightsSecurity Lights Common Applications Commercial parking lots Private roads and streets Warehouses Schools and campuses Industrial properties HOAs and communities Sports areas Why Use a Double Bullhorn? Mount two fixtures on one pole Create opposing 180° positions Direct light toward two areas Use compatible 2-3/8" slip fitters Create a clean pole-top layout Installation Planning 1Measure Pole Verify actual outside diameter.2Check Fixtures Confirm 2-3/8" slip-fitter compatibility.3Verify Structure Account for fixtures, wind, pole and foundation.4Install & Aim Secure and aim according to the lighting layout. Structural note: Adding a second fixture increases weight and wind-exposed area. Confirm the complete assembly is suitable for the actual fixtures and site conditions. Product Specifications Product Type 180° Double Bullhorn / Twin Tenon Bracket Configuration Two Opposing Horizontal Mounts Fixture Positions 2 Designed Pole Compatible 3" Round Pole Center Mount ID Approx. 3.2" Center Mount OD Approx. 3.5" Fixture Tenons 2-3/8" OD Each Material Welded Steel Color Black Approx. Size 20" L × 3.5" W × 7.1" H Mounting Hardware M10 Mounting Bolts Listed as Included Typical Fixtures Shoebox, Parking Lot, Area, Flood, Security & Street Lights What's Included 1 × 180° Double Bullhorn Bracket 2 × Integrated 2-3/8" OD Tenons M10 mounting bolts as listed Fixtures, pole and other site-specific hardware are not stated as included.Before You Buy Measure pole diameter Check fixture slip-fitter size Confirm fixture weights Confirm pole and foundation capacity Review wind loading where required Questions & Answers What size pole does this bracket fit?It is designed for a compatible 3-inch round pole. The supplied center sleeve is approximately 3.2" ID and 3.5" OD. Measure your actual pole before ordering. What size are the two fixture arms?Each horizontal arm is approximately 2-3/8" outside diameter for compatible slip-fitter fixtures. Can I mount two lights on one pole?Yes. It creates two opposing fixture positions. The pole and foundation must support the complete assembly and applicable environmental loads. Are the lights positioned 180 degrees apart?Yes. This is an opposing 180-degree double bullhorn configuration. Will it fit a shoebox parking lot light?It can fit many shoebox lights using a slip fitter designed for a 2-3/8" OD tenon. Check the exact fixture specification first. Can I use it with street, area or flood lights?Yes, when the fixture uses a compatible 2-3/8" slip-fitter mount and the pole assembly is structurally suitable. Do I need another slip-fitter adapter?The two horizontal arms are already 2-3/8" OD tenons. A separate fixture adapter is not normally needed when the light has a compatible slip fitter. What is the bracket made from?The supplied information lists welded steel construction with a black finish. What are the approximate dimensions?Approximately 20" long × 3.5" wide × 7.1" high. Are the lights and pole included?No. This listing is for the bullhorn bracket and listed mounting hardware. Fixtures and pole are not stated as included. Can I add two large fixtures without checking my pole?No. Two fixtures increase total weight and wind-exposed area. Verify the pole, foundation and mounting assembly for the actual fixtures and site. How can I confirm my 3-inch pole will fit?Measure the actual outside diameter of the pole and compare it with the approximately 3.2" center-sleeve inside diameter. Not Sure If It Fits? Send Outdoor Solar Outlet your pole outside diameter and the mounting dimensions or product link for your fixture. We can help compare the measurements before ordering. Ask About CompatibilityCall 1-877-488-3581