Oil-Filled Canister Style Remote Ignition Coil - Female
Restore or upgrade your classic distributor ignition system with the Top Street Performance Oil-Filled Canister Style Remote Ignition Coil with female connector. Delivering up to 45,000 volts of maximum output with a 350ms spark duration and 100:1 turns ratio, this high-output canister coil is engineered to bring consistent, reliable spark energy back to external-coil distributor ignition systems found in classic Chevrolet, Ford, Mopar, and other carbureted V8 applications. The female connector configuration makes this coil a direct match for distributor ignition wiring harnesses that use a female terminal connection at the coil — a common setup in many classic and vintage ignition systems. Whether you're refreshing a tired points-style ignition, upgrading to a more reliable electronic distributor setup, or replacing a weak coil on a street rod, muscle car, or hot rod build, this canister coil delivers the voltage output, heat resistance, and period-correct canister styling your ignition system needs. The oil-filled internal construction provides superior heat dissipation compared to epoxy-filled coils, helping the coil maintain consistent output during sustained driving, extended idle, and high-demand performance conditions. The round billet aluminum housing provides a clean, durable exterior that complements custom engine bays, vintage ignition setups, and show-quality builds. A mounting bracket is included for straightforward installation on a wide range of engine and firewall mounting configurations. With a primary resistance of 0.7 Ohms, secondary resistance of 4,700 Ohms, peak current of 140mA, and inductance of 8.0 millihenrys, this coil is engineered to meet the electrical requirements of most distributor-based ignition systems. Available in Black, Red, Blue, and Chrome to match your build's style. Oil-Filled Canister Coil Technology The oil-filled internal construction is a key performance and durability advantage of this canister-style ignition coil. Unlike epoxy-filled coils, the oil-filled design allows heat generated during operation to transfer away from the coil's windings more effectively, helping maintain consistent electrical output across a wide range of operating temperatures. This thermal management capability makes oil-filled canister coils a preferred choice for classic car restorers, street rod builders, and performance enthusiasts who demand dependable ignition performance in engine bays that can generate significant heat. The round billet aluminum housing further supports heat dissipation while providing the classic canister profile that looks at home in vintage and custom engine bays alike. The coil must be mounted vertically to maintain proper oil distribution within the housing. Performance Benefits With a maximum output of 45,000 volts, a 350ms spark duration, and a 100:1 turns ratio, this ignition coil delivers strong, consistent spark energy across the full operating range of a distributor-based ignition system. The 0.7 Ohm primary resistance is matched to the requirements of most electronic and points-style distributor ignition systems, supporting reliable ignition timing, cleaner combustion, and more consistent engine operation from cold start through wide-open throttle. For classic carbureted V8 builds where ignition reliability is critical to consistent performance, upgrading to a high-output canister coil is one of the most effective and cost-efficient ignition improvements available. Common Applications This oil-filled canister coil is well-suited for a wide range of classic and performance ignition applications including classic Chevrolet small block and big block V8 builds, Ford small block Windsor and FE V8 applications, Mopar small block and big block distributor ignition systems, street rods, hot rods, muscle car restorations, and custom carbureted V8 builds using external-coil distributor ignition configurations. It is also commonly used in electronic distributor conversion projects where an upgraded coil is needed to support the higher energy demands of an electronic ignition module. COMPATIBLE WITH UNIVERSAL DISTRIBUTOR-BASED IGNITION SYSTEMS • Points ignition systems • Electronic distributor ignition systems • HEI conversions using an external canister coil • Classic carbureted ignition systems with a remote-mounted canister coil COMMON VEHICLE APPLICATIONS Classic Chevrolet ignition systems Classic Ford ignition systems Classic Mopar ignition systems Street rods Muscle cars Carbureted V8 builds Distributor replacement and ignition upgrades Restoration projects NOTES • Universal remote-mounted canister ignition coil. • Compatible with points, electronic, and HEI ignition systems that use an external coil. • Oil-filled design must be mounted vertically. • Verify ballast resistor requirements before installation. • Verify wiring polarity and distributor compatibility before installation. • Not compatible with HEI distributors that use an in-cap ignition coil. SPECIFICATIONS Coil Style: Canister Color: Black Internal Construction: Oil-Filled Primary Resistance: 0.7 Ohms Secondary Resistance: 4700 Ohms Maximum Voltage: 45000 V Spark Duration: 350 Ms Peak Current: 140 Ma Turns Ratio: 100:1 Inductance: 8.0 Millihenrys (Mh) Mh Coil Shape: Round Housing Material: Billet Aluminum Coil Wire Attachment: Female Included: Mounting Bracket