Madison 100% Premium Acrylic Latex Paint from A&L Paint Company

The same paint used on our BYC Lighthouses, Windmills and on much of our Amish-Made Furniture. Small batch premium paint made on an Amish Farm in Pennsylvania and shipped FRESH to your door directly from the manufacturer! Madison Paint has a very high solids content which results in more surface coverage per gallon, and a lower cost per square foot. A&L uses high quality ground pigments which give you better color retention and longevity for a high quality end result. Madison is a very low odor paint that sprays or brushes on smooth and is easy to touch up. Madison is SELF-PRIMING and has great adhesion. It produces early water resistance and will adhere to chalky and weathered surfaces as well as new smooth surfaces, without flaking or peeling. You can expect consistent colors and results. Madison is designed for use on wood, concrete blocks, pre-primed metal, primed siding, cement board, storage sheds, barns and houses. Actual colors may vary from the images displayed here. We strongly recommend that you view actual color samples before making a final color selection. Paint samples may be requested. CUSTOMER COLORS are available. Call or email for more information. A&L can match their well known competitors colors with ease and FREE OF CHARGE. Note: In addition to the sizes on this listing, Madison Paint is also available in 55 gallon drums which are perfect for large-scale projects and contracting needs. Contact us for pricing. Application Instructions Outdoors: Apply under optimal conditions: Ideal temperatures are between 65 and 75 degrees with humidity not greater than 50%. Avoid applying during high temperatures, in direct sunlight, or on hot surfaces as this will cause the paint to dry to quickly and hinder proper penetration. Indoors when using a sprayer: The ideal room and product temperature is between 60- 80 degrees. Warmer room air temperatures may cause the coating to dry too quickly at the edges of the spray fan causing a dusty over spray. Cooler temperatures will slow drying times. The Madison Paint temperature should be similar to the room temperature for best results. Substrate temperature should be consistent with the room and coating temperature. The siding must be dry and free of dirt or dust. Consistent temperatures of the spray room, coating and substrate are important for the proper application of Madison Paint. Equipment Spray equipment must be maintained and working properly for best results. We recommend using a 517 tip. Equipment recommendations are general and can vary with the personal preferences and requirements of each person doing the application. We recommend that those doing the application experiment with different tips and find what works best for your situation and circumstances. Begin by making sure your sprayer pressure is correct. Spray a test panel and lower the sprayer pressure until there are fluid streaks at the outside edge of the spray fan. Gradually increase the pressure until the streaks go away. Make a note of the pressure for future reference. Different sprayers may require different pressures so be sure to test a new or different sprayer before spraying a barn. Apply the first coat with even, up and down strokes holding the spray fan in the center of each groove in the siding. Fan width and coating volume may vary a little depending on your tip and equipment but with the recommended tip sizes there should be very little difference. Wait until the first coat has dried then apply the second coat. Application By brush, roller or sprayer We recommend a two coat application process. Apply the first light coat and wait until it’s dry then apply a second coat. Ventilation Ventilation of the spray room is critical for timely drying of Madison Paint. The spraying process of this waterborne coating creates moisture in the air that needs to be ventilated out of the room for quicker drying. Air movement needs to be through and out of the spray room, not just around the spray room. The best way to do this is to have a fresh air intake of some kind, even if it’s a window or door, and exhaust fans at the other end of the room blowing air to the outside. The more moisture you move out of the spray room with ventilation the quicker the coating will dry. The less air you move through the longer it will take to dry. Humid and colder air will slow drying times. Spread Rate . . . . . . . .400 – 600 % (NVM) . . . . . . . . . . . . .43 – 48 VOC’s . . . . . . . . . . . . . <60 (G/L) UV Resistance . . . . . . . . . Pass Mold & Mildew Resistance . . . . . . . . . . . . Pass Dry time: to touch. . . . . . . . . . 30 minutes to handle. . . . . . . . . 60 minutes to topcoat. . . . . . . . . 30 minutes to cured. . . . . . . . . .. . . . 7 days