StoneTech™ High Gloss Finishing Sealer for Stone

Enhances the beauty of natural stone and POROUS tile with an innovative, water-based gloss finishing sealer Two-in-one formula leaves a wet-look finish to stone floors and protects against stains. Interior use only - not for exterior use! Not for use on glazed ceramic tile! PLEASE NOTE PRODUCT NOT FOR SALE IN CALIFORNIA StoneTech® High Gloss Stone Floor Sealer from Bane-Clene® Corp. StoneTech High Gloss Stone Floor Sealer enhances the beauty of natural stone and POROUS tile with an innovative, water-based, low-odor high-gloss finishing sealer that provides subtle shine and delivers long-lasting protection against oil- and water-based stains. Features and Benefits of StoneTech High Gloss Stone Sealer: Two-in-one formula leaves a wet-look high-gloss finish to stone floors and protects against stains. Easy to use, water-based formula. Low-odor. Enhances the beauty of natural stone and POROUS tile Imparts long-lasting protection against oil- and water-based stains Provides brilliant shine and deepens color. Topical coating. Properties & Specifications: Restrictions on Use: Professional Use Only. Keep out of reach of children. Form: Liquid. Size: Available in single gallons. Manufacturer: StoneTech® / Laticrete® International. Country of Manufacture: United States of America. Storage: Do not freeze or store above 100°F. Keep container tightly closed when not in use. Store in a cool and well-ventilated place. Odor: Slight, acrylic-like. Color: White. Use pH: 8.7. Quantity: Available in single gallons. Coverage: Up to 300 square feet per gallon depending on porosity of stone surface. Full Cure: 24 - 48 hours. Expected Wear: Up to 5 years. Touch up on higher traffic areas may be required on a more frequent basis. VOC content: <85 g/L. Flammability: Non-flammable. Where to Use High Gloss Stone Floor Sealer: Concrete (interior only). Flagstone Marble. Mexican and Saltillo Tile. Slate. Textured Limestone. Textured Travertine Where NOT to Use High Gloss Stone Floor Sealer: NOT for exterior use! - interior use only - NOT for use on glazed tile! NOT intended for use on glazed, polished or non-absorbing surfaces, wood floors & decks, showers, countertops or near pool areas. NOT recommended for showers or surfaces that stay wet. Instructions and Directions for High Gloss Stone Sealer: Restrictions and Warnings before Applying High-Gloss Stone Sealer: Read entire label and SDS (Safety Data Sheet) before using. Use only as directed. Always test in a small inconspicuous area to determine appropriate application method, achievement of desired results, and to ensure good adhesion. Avoid applying in direct sunlight. Surface temperature should be 50°F - 80°F. STONETECH High Gloss Finishing Sealer should not be applied a wet or moist surface. Avoid applying onto surfaces not intended for treatment. For new installations with grout, sealer can be applied as soon as 72 hours after grouting. Fresh concrete slabs require a minimum of 28 days to cure before applying the sealer. Keep children and pets out of the area until foot traffic resumes. Surface Preparation: Surface must be thoroughly clean, dry, and free of any sealers or coatings before application. Application to a dirty or dusty surface will affect adhesion and appearance. Clean surface with Klenz-All™, rinse and dry thoroughly Follow these Steps to Apply High Gloss Stone Sealer to a Stone Surface: Ensure work area is well-ventilated during application and until surface is dry. SHAKE WELL BEFORE USING. Do not dilute before applying. Liberally apply 1-3 even coats of STONETECH High Gloss Finishing Sealer with a natural bristle paint brush, paint pad or paint roller. Do not apply product with a sprayer, which might leave bubbles. Do not apply with a sponge. Failure to apply a sufficient amount of sealer to the surface may result in an undesirable finish or degradation of the coating. More coats may be applied if desired. Avoid puddling or bubbling or foaming of product during application. Allow 30 - 45 minutes between coats or until the surface is dry to the touch. Surface traffic may begin 12 hours after final application. Keep installation dry for a minimum of 12 hours. Full cure is achieved in 24-48 hours. Keep surfaces clean and dry as finished surfaces may become slippery when wet. Clean tools used during application immediately with water. Maintenance of Stone Surfaces Sealed with High Gloss Stone Sealer: Highly alkaline, acidic, ammoniated, and/or abrasive cleaners are not necessary for daily maintenance and may also degrade the sealer, adversely affecting stain resistance. To maintain stone’s natural beauty, clean surface as needed with Revitalizer™ Cleaner and Protector or All Purpose Stone & Tile Cleaner Concentrate. For tough or difficult to remove soil use STONETECH KlenzAll™ Cleaner and a nylon scrubbing pad or a long handled stiff bristle brush. Please note: Prior to using any cleaning material on a tile, stone, etc. installation, test a discrete area or scrap piece of tile to ensure desired results. Additional Stone, Ceramic and Porcelain Tile & Grout Information: Dates for Training Classes for Cleaning Professionals Limestone Marble Mexican and Saltillo Tile Porcelain Tile and Grout Sandstone Slate StoneTech™ Terrazzo Travertine VIDEO: How to Clean Natural Stone, Marble, Granite, etc. VIDEO: How to Protect and Seal Natural Stone like Marble, Limestone, Granite, Travertine Usage & Tips Specifications Coverage Approximately 100 to 300 sq. ft. per gallon depending on stone, porosity, texture of surface and method of application. Safety Data Sheets Link ST 61221 SDS (PDF)