Two DC 24V Thrust 1800 lb Heavy Duty Linear Actuators Sync Control Kit

Note: 1) This product does not contain a mounting brackets. If needed, please click here to buy. 2) If you need a 24V 25A power supply to power this kit, please click here to buy. 3) If you need external limit switch for linear actuator, please click here to choose and buy. Package Include 2 x Electric Linear Actuator C with Hall Effect Sensor 1 x Synchronous Controller (One-Control-Two, For 2 Linear Actuator C) 1 x Touch Control Handle 1 x Remote Control (CH-3) 1 x User manual The information for electric linear actuator Application: Mainly used for doors, windows, cellars, trapdoors, hatchways, solar tracking system, medical devices, agricultural machinery, vehicles, ships, elevator platforms, lifting tables, TV lifts, robots, cabinetries, massage sofas, electric beds, medical chairs, and other electrical equipment. It can open, close, push, pull, lift, and descend these devices. It can replace hydraulic and pneumatic products to save power consumption. Feature: High-quality products and high-quality services Metal housing, able to work in very harsh environments Metal gearbox and high strength wear-resistant metal gears Stainless steel telescopic tube and outer tube, good corrosion resistant Heavy duty design, high-power DC motor Advanced waterproof and dustproof technology Low power consumption and low noise Built-in clutch to protect gears and motors Built-in motor overload and overheat protection Built-in two limit switches, linear actuator will automatically stop when stroke rod reaches the limit position. Built-in Hall sensor, so you can use the synchronous controller to operate 2 linear actuators fully synchronously. With auto-locking capability to hold load position after stopping, and no power supply is required. Maintenance-free Specifications: Working voltage: DC 24V Stroke range: 4~ 24 inches or 100~ 600 mm Optional speed: 5±1mm/s, 8±2mm/s, 10±2mm/s, 12±2mm/s, 16±3mm/s, 20±4mm/s The above is the speed at no load, and the actual working speed will gradually slow down as the load increases. Max Load capacity: 8000N / 800 Kgs / 1800 lbs at 5mm/s Linear actuator can get maximum load capacity when it operates in the vertical direction, and the pulling force is less than pushing force. No-load current: 1~1.5A at 24V Full load current: 6~10A at 24V Please use a 24V 25A power supply to power the two linear actuators. Shaft diameter: 28mm The diameter of the mounting holes for the front and rear connectors: 13mm [0.512 in] Housing Material: Stainless steel Stroke Rod Material: Stainless steel Gear Material: Steel Alloy Motor Type: Brushed DC Motor Duty cycle: 10%, max 2mins continuous use Service life: approx. 35, 000 cycles Power cable: Six-pin Plug Cable length: 2500±10%mm [24 in], the length can also be customized according to your specific needs. Certifications: CE Environment temperature: -26℃ to 85℃ Operating Noise: about 56dB~66dB (Linear actuators with different parameters will have different noise levels.) IP rating: IP65 Different speeds and corresponding maximum thrust No-load Speed Full load Speed Maximum Thrust Self-locking Force 5mm/s 3.5mm/s 8000N / 800 kg / 1800 lbs 8500N / 850 kg / 1900 lbs 8mm/s 6mm/s 7000N / 700 kg / 1600 lbs 7500N / 750 kg / 1700 lbs 10mm/s 7mm/s 6000N / 600 kg / 1300 lbs 6500N / 650 kg / 1500 lbs 12mm/s 9mm/s 5000N / 500 kg / 1100 lbs 5500N / 550 kg / 1200 lbs 16mm/s 12mm/s 4000N / 400 kg / 880 lbs 4500N / 450 kg / 1000 lbs 20mm/s 15mm/s 3000N / 300 kg / 670 lbs 3500N / 350 kg / 790 lbs The information for synchronous controller Introduction: If you want to use multiple linear actuators to raise and lower an equipment, for example two, three or four electric actuators. Since the high-speed DC motors in electric actuators cannot run at exactly the same speed, so the movement speed of the electric actuator will also be different. When multiple electric actuators work at the same time, their actual speeds cannot be exactly the same. In this case, we can use a synchronous controller to operate multiple linear actuators to rise or fall synchronously. They work completely in sync without any difference. Working principle: If you want to use a synchronization controller to operate 2, 3 or 4 linear actuators fully synchronously, you will need to add built-in Hall effect sensors for each linear actuator. And when you have purchased Hall effect sensors along with linear actuators, we will install Hall effect sensors in the linear actuators during production for you. When 2, 3 or 4 linear actuators are running together, Hall sensor will send Hall signals to the synchronization controller, and the controller will adjust the running speed of each linear actuator, so that all linear actuators run at the exact same speed. Feature: It can operate two electric linear actuators C to run completely synchronously. Wired control via a touch control handle. Wireless control via a remote. The LED display on the control handle and remote control will display the stroke position in real time. Six touch function buttons: ▲, ▼, 1, 2, 3 and R. Buttons ▲ and ▼ are used to operate the linear actuators extension and retraction. Buttons 1, 2 and 3 are used to automatically operate the linear actuators to three pre-memorized positions. Button R is the reset button and is used to reset the system in case of an error. With external limit switch control function With a reset button and pairing button When linear actuators move close to the end position, they will automatically slow down to protect themselves. When linear actuators are fully retracted, they will retain 1MM of travel to protect themselves. Parameters: Working Voltage: 12~48 VDC, suitable for 12V or 24V linear actuator Number of connecting linear actuators: 2 Working Frequency: 2.4 GHz Working Distance: 10m / 30ft (theoretically) Rated current: 25A Control modes: Interlocking mode Operating Temperature: -20°C ~ +70°C Case size: 130 x 120 x 50 mm Cable length of the touch control handle: 2000±10%MM [80 in] Connection: 1) Plug the touch control handle into the port Hand Set of the controller. 2) As shown in the diagram, plug the two terminals of the first linear actuator into the two ports of CH1 on the controller, and plug the two terminals of the second linear actuator into the two ports of CH2 on the controller. 3) Connect the positive pole of DC power supply to the power terminal + of the controller, and connect the negative pole of DC power supply to the power terminal - of the controller. Operation via the touch control handle: Attention: The handle is operated by touch control. The touch sensitivity can be automatically calibrated when powered on for the first time. Hands are prohibited from touching the handle when powered on to prevent interference with the sensitivity calibration and affect the operating sensitivity. 1) Press and hold the ▲ button of the control handle, two linear actuators extend outward at the same time; Release the button, two linear actuators stop at the same time. 2) Press and hold the ▼ button of the control handle, two linear actuators retract inward at the same time; Release the button, two linear actuators stop at the same time. 3) Press any of the button 1, 2, or 3 on the control handle, two linear actuators will automatically move to the position memorized by that button and then automatically stop. Note: You will need to first memorize three positions into these three buttons. 4) The LED display on the control handle will display the stroke position data in real time. For example, the number 03.5 means that the linear actuators have reached the stroke position of 35MM. Operation via remote control: 1) Press the button ▲ of the remote control, two linear actuators extend out at the same time, they will reach the maximum stroke at the same time and stop automatically. 2) Press the button ▼ of the remote control, two linear actuators retract inward at the same time, they will fully retract at the same time and stop automatically. 3) During operation, you can press the stop button or any button of the remote control to stop two linear actuators at the same time. External limit switch control function: You can connect two external limit switches with normally open contact (such as model 0010010) to this controller and then automatically stop the linear actuators through it. 1) You can connect two limit switches, and each limit switch has two normally open terminals. 2) Connect two normally open terminals of a limit switch to terminals UP and COM on the controller, connect two normally open terminals of another limit switch to terminals DOWN and COM on the controller. The operation: 1) When two linear actuators extend outward, if the limit switch is triggered, it will connect two terminals UP and COM, then two linear actuators will stop automatically. 2) When two linear actuators inward retract, if the limit switch is triggered, it will connect two terminals DOWN and COM, then two linear actuators will stop automatically. How to memorize three stroke positions: 1) The controller can memorize total three stroke positions, and each button memorizes one stroke position. 2) First operate two linear actuators to the first suitable stroke position that you need to store, then press and hold the button 1 of the control handle for about 5 seconds, the stroke value on the LED display will flash. This means that the current stroke position is already stored in button 1. 3) You can continue to store the other two stroke positions into the button 2 and 3 by following the operation above. Reset Function: When the LED display on the control handle shows the fault code, you need to reset the system as follows. Reset operation: Press and hold the R button of the control handle or the button on the controller, until all linear actuators are reset to the bottom, and the LED display on the control handle shows "00.0", then release the button. Production Time and Return or Exchange Policy The linear actuators are customized and not in stock, and we need to spend 3~7 working days to produce them according to the specified parameters in your order, so that we don't accept returns or cancel orders. If customers order unsuitable linear actuators themselves, we also do not accept exchanges, please understand.