2016–2023 Toyota Tacoma LED Ditch Light Kit – F1 Black Series

Built for 2016–2023 Toyota Tacoma Dual-Beam LED Ditch Lights. One Complete Kit. Add wide-area auxiliary lighting to your Tacoma with a pair of FUZED F1 Black Series 3-inch LED pods, vehicle-specific hood brackets, a relay wiring harness and a dual push-button switch. The low- and high-beam functions operate independently—or together when you want both patterns. Quick-connect switch wiring helps simplify installation without splicing multiple wire ends. Independent dual-beam controlVehicle-specific bracketsReal-world tested Vehicle-specific hood-hinge mounting. What's included Everything you need for the lighting upgrade Standard kit includes: Two FUZED F1 Black Series 3-inch LED pods Pair of 2016–2023 Tacoma hood-hinge mounting brackets Relay and wiring harness Dual push-button switch for separate low- and high-beam operation Supplied mounting hardware Optional relay mounting bracket sold separately. Kit contents and hardware should be confirmed against the final packaged product. Real-world light output See the difference between each beam mode These photos show the same off-road scene with the independently controlled low beam, high beam and both beams together. Low beam: Low-beam flood pattern shown in our night test. High beam: High-beam flood pattern shown in our night test. Both beams: Combined foreground and elevated coverage. Measured in our installation test 1,181 lux at 20 feet Hotspot reading with both LED pods illuminated and both beam functions activated, measured at 20 feet during our Tacoma installation test. Lux measures illumination at the meter, not total lumen output. Results vary with aiming, distance and test conditions. Independent control Low beam, high beam—or both The included dual push-button switch gives you separate control of the two beam functions. Choose the pattern that fits your off-road conditions without needing to activate both every time. Mounting and wiring are demonstrated in our installation walkthrough below. Dual push-button control for independent beam functions. Optional relay mounting bracket, shown separately. Optional upgrade Add a relay mounting bracket Choose the optional relay mounting bracket for a dedicated mounting point for the relay assembly and a tidier engine-bay installation. Not included with the standard kit. Select the bracket upgrade using the product option above the Add to Cart button. Product details Specifications & fitment Vehicle2016–2023 Toyota Tacoma* Pod size3-inch F1 Black Series Beam modesLow / high / combined ControlIndependent dual push-button switch Operating voltageDC 10–35V (manufacturer spec) Waterproof ratingIP68 (manufacturer claim) Light colorCool white Tested output1,181 lux at 20 ft, combined *Confirm compatibility with any aftermarket hoods, cowl accessories or other equipment before purchase. Auxiliary lights may be restricted on public roads; follow applicable local laws. Installation View the full installation walkthrough Follow our Tacoma-specific mounting, quick-connect switch wiring, relay installation, and aiming walkthrough. The photo steps stay collapsed until you need them. Watch the complete installation and night test View Installation Instructions — 13 Photo Steps Quick-connect switch wiring: In the filmed installation, matching colors connect together except the harness white wire, which connects to the switch green wire. Check the wiring diagram supplied with your specific switch and harness before connecting. The optional switch backlight was not wired in this video. Before you begin: Park safely with the ignition off and follow the vehicle and harness safety instructions. Disconnect the negative battery terminal before electrical work. Support the hood while loosening hinge fasteners, protect existing wiring and grommets, and verify clearance before driving. Step 1. Install the Tacoma hood-hinge bracket Remove the upper hood-hinge bolt, position the ditch-light bracket, then loosely reinstall the bolt. Support the hood while removing the lower bolt. Align the bracket using the original hinge marks, check clearance behind the hood, tighten the hinge fasteners to the vehicle manufacturer’s specification, and return the washer-fluid hose to its original position. Watch this step in the video → Step 2. Attach the LED pod mounting hardware Remove the pod’s original bracket using the supplied Torx tool, then attach the mounting hardware to the Tacoma-specific ditch-light bracket. Leave adjustment hardware slightly loose for aiming. Watch this step in the video → Step 3. Mount both LED pods and check clearance Align the pod mounting holes and install the fasteners. Repeat on the opposite side. With the hood fully open, confirm that the pods clear the windshield and surrounding bodywork. Watch this step in the video → Step 4. Lay out the relay wiring harness Position the relay leads near the battery. Route the longer pod lead toward the passenger side and the shorter lead toward the driver side. Plan to secure the excess driver-side wire after testing. Watch this step in the video → Step 5. Feed the switch wires through the firewall Route the switch wiring toward an existing rubber firewall grommet. In the video, the supplied hook tool is used to guide the wires through a small opening in the grommet. Protect the wire insulation and reseal the opening to prevent water intrusion. Watch this step in the video → Step 6. Install and connect the correct-size switch Choose the switch size that matches an available Tacoma dash opening; some trucks have an existing accessory switch occupying the smaller position. Remove the blank, fit the supplied dual switch, and connect the wiring. The video demonstrates the quick-connect system without wire-end splicing. Watch this step in the video → Step 7. Fit the optional relay mounting bracket If you selected the relay mounting bracket upgrade, install it at the demonstrated engine-bay mounting point using the supplied hardware. This bracket is optional and not part of the standard kit. Watch this step in the video → Step 8. Secure the relay assembly Mount the relay assembly to the optional bracket, if fitted, using the included hardware. Otherwise, secure the relays according to the supplied harness instructions, away from moving parts and heat. Watch this step in the video → Step 9. Connect the pods and secure the harness Route each pod lead through the opening shown near the hood seal. Align the keyed waterproof connectors, push them fully together, and tighten their locking collars. Keep the wiring clear of the hood seal and hinge movement. Watch this step in the video → Step 10. Connect battery power safely With the ignition off, verify the harness fuse and polarity against the supplied wiring diagram. For a conventional negative-ground battery, connect the positive supply first and the negative/ground last. The video shows a different connection order; follow the safer sequence and the vehicle/harness instructions. Watch this step in the video → Step 11. Test the low and high beam modes Check the switch and test low beam, high beam, and both together. The video explains that matching wire colors are joined through quick connectors except the harness white wire, which connects to the switch green wire for the demonstrated switch configuration. Verify colors against your kit’s current wiring diagram before making connections. Watch this step in the video → Step 12. Tuck away and secure the wiring Bundle excess harness length and secure it alongside existing engine-bay wiring, as shown in the video. Keep wires away from hot surfaces, sharp edges, and moving components. Confirm the hood opens and closes without catching the harness. Watch this step in the video → Step 13. Aim the pods and tighten the hardware Remove the protective film from the lenses. Aim the pods for your intended off-road use, then tighten the lower mounting nut with a 13 mm wrench and the side adjustment fasteners with the supplied Torx tool. Protect the hood paint and recheck clearance. Watch this step in the video → These photos provide an overview, not a substitute for the instructions supplied with your wiring harness. Installation details can vary by vehicle configuration. Common questions Frequently asked questions Can the low and high beams operate separately? Yes. The included dual push-button switch allows independent low- and high-beam operation, or both together. Is the relay mounting bracket included? No. The relay mounting bracket is an optional add-on; the standard kit includes the relay/wiring harness. Does this kit include the hood mounting brackets? Yes. The standard kit includes a pair of Tacoma-specific hood-hinge mounting brackets. Is the 1,181-lux figure for one light? No. The reading was taken at the hotspot from both pods together, with low and high beams activated, at a 20-foot distance. Can I use these lights on public roads? These are auxiliary off-road lights. Laws governing use and required covers vary by location. Check your local regulations before using them on public roads.