Proline X Micro Series 10" Sealed Enclosure - Fits ResoNix GUS 10

Micro Series | GUS-10 | Enclosure Only Built for the ResoNix GUS-10. Klippel-Verified Performance in 6 Inches of Depth. The ResoNix GUS-10 has a measured Fs of 16.91 Hz, a Qts of 0.35, and Klippel-verified Xmax of 18.37mm at BL 70% — the same engineering platform as the GUS-12 and GUS-15, scaled to a 10" format. The Proline X Micro Series enclosure delivers 0.63 cubic feet of sealed airspace in a double-layer stack-fab build at 6 inches of total depth — near ResoNix's 0.60 cubic foot optimum in the most compact shell in the GUS Micro Series lineup. 0.63 Cu Ft Net Volume 6" Total Depth 16.91 Driver Fs (Hz) 500W Driver RMS Rating Enclosure only. The ResoNix GUS-10 subwoofer is not included and must be purchased separately from ResoNix Sound Solutions. This enclosure accepts both the D2 and D4 variants — the cutout and mounting geometry are identical between impedance options. 0.63 cu ft — Near ResoNix's 0.60 Optimum ResoNix publishes a 0.707 Qtc target of 0.60 cubic feet for the GUS-10, with a driver displacement of 0.031 cubic feet. The correct gross build volume to deliver exactly 0.60 cubic feet of net acoustic airspace after the driver is installed is 0.60 + 0.031 = 0.631 cubic feet. This enclosure delivers 0.63 cubic feet net — hitting ResoNix's 0.60 acoustic target, which places the system Qtc fractionally above 0.707 and shifts the anechoic -3dB point marginally upward. In a real vehicle cabin, where bass frequencies below 80 Hz receive significant gain from acoustic boundaries, the difference between 0.60 and 0.63 cubic feet net is not audible. The GUS-10 in this enclosure performs within the band of ResoNix's published optimum range, and with active DSP shelf EQ the in-cabin response is fully correctable to any target curve the driver's T/S parameters support. The GUS-10 — Same Platform as the GUS-12 and GUS-15, in a 10" Format The GUS-10 shares the core engineering of the GUS-12 and GUS-15: FEA-optimized overhung motor, patent-pending copper shorting sleeve, copper shorting rings, titanium voice coil former, Nomex/carbon fiber cone, and vented rear cone assembly. Every major parameter is Klippel-verified. The BL(x), CMS(x), Le(x), and QTS(x) data is published. The GUS-10 is the entry point into the GUS series — 500 watts RMS, 18.37mm one-way Xmax at BL 70%, Fs of 16.91 Hz, and Qts of 0.35. Like the GUS-12, the low Qts means DSP is the correct operating environment for this driver. At 0.707 Qtc the anechoic response is flat and extended but lean in the upper bass without active shelf EQ. A Goldhorn DSP or equivalent processor is the right companion. The GUS-10 is the front subwoofer platform on the enthusiast market right now — its 4.12" mounting depth and compact sealed enclosure footprint put it in locations where nothing else with its distortion performance and extension capability can go. 1.5" Double-Layer Baffle — Stack Fab, Dado Joinery, Dowel Reinforced The front baffle is a double-layer stack-fab build — two CNC-cut Langboard Elite MDF panels bonded to 1.5 inches total. The stack-fab assembly is further reinforced with dowels throughout, adding mechanical alignment and shear resistance at every panel joint beyond what dado joinery and adhesive alone provide. At 500 watts RMS on a 10" driver with 18.37mm of one-way Xmax, the structural demands on the baffle are real — double-layer construction eliminates panel resonance at the source rather than allowing it to color the bass output. Every panel joint uses CNC-cut interlocking dado slots. The 6-inch total depth gives side walls adequate geometric rigidity for the load, and Langboard Elite MDF at 200 psi internal bond and 410,000 psi MOE holds the structure over the life of the installation. Volume 0.63 cu ft — Near ResoNix's 0.60 Optimum ResoNix's 0.707 Qtc target is 0.60 cu ft net acoustic. This enclosure delivers 0.63 cu ft — within the functional band of that target. With active DSP, the marginal Qtc difference is correctable and acoustically irrelevant in-cabin. Driver Klippel-Verified 18.37mm Xmax — Published LSI Data The GUS-10's 18.37mm Xmax at BL 70% is a Klippel large-signal measurement. BL symmetry, CMS linearity, and Le stability across stroke are all published by ResoNix — the same transparency standard applied to every driver they independently test. Baffle 1.5" Double-Layer — Dowel Reinforced Stack Fab Two bonded layers of Langboard Elite 3/4" MDF at 1.5 inches total, reinforced with dowels throughout the stack-fab assembly. Baffle panel resonance adds acoustic coloration — double-layer construction at 1.5 inches eliminates it structurally. Mounting 8/32 Threaded Inserts — Machine Screws Included The baffle is fitted with 8/32 threaded inserts on the back face. Stainless machine screws are included. The GUS-10 mounts to steel — consistent clamping force, no stripping, clean reinstallation at any service interval. Wiring Proline X Terminal Cup — Pre-Wired with 12g OFC The Proline X ABS/carbon fiber terminal cup with stainless hardware and copper ring terminals is installed and pre-wired with 12-gauge OFC to the driver position. Connect your amplifier run and wiring is complete. Cutout 235.3mm Direct-Fit — Machined for the GUS-10 The baffle cutout is machined to the GUS-10's 235.3mm mounting diameter. The driver seats flush, seals against the included rubber mounting ring gasket, and mounts to the threaded inserts without shimming or modification. DSP Active EQ Required — Same Character as the GUS-12 The GUS-10's Qts of 0.35 and Fs of 16.91 Hz produce a 0.707 Qtc sealed alignment — flat anechoic response that needs active shelf EQ to build the in-cabin curve. A Goldhorn DSP or equivalent is the correct companion. Without EQ, upper bass will sound lean — that is the alignment doing what it was designed to do. Configuration Front-Firing or Downfiring — Feet Included Rubber feet for downfiring installation are included. The GUS-10's vented rear cone assembly allows the pole vent to be fully obstructed — downfire in a tight enclosure is viable with no acoustic penalty. ResoNix notes minimal real-world difference between orientations; choose based on install practicality. Clearance 23mm Minimum Front Clearance ResoNix specifies a minimum of 23mm of clearance between the top of the GUS-10's surround and whatever is in front of the driver. Confirm this against your seat, cargo cover, or any surface positioned in front of the driver before mounting. Surround contact at full excursion causes mechanical damage not covered under warranty. Reinforcement Dowel-Reinforced Stack Fab — Three Systems at Every Joint Dowels throughout the stack-fab assembly add mechanical alignment and shear resistance at panel joints independent of adhesive condition. Dado joinery + adhesive + dowels — all three mechanical systems locking every joint against sustained load over the life of the installation. Ready to Mount. Ready to Wire. Built for DSP Systems. The enclosure ships fully prepped. The Proline X terminal cup is installed and pre-wired with 12-gauge OFC — connect your amplifier run and wiring is complete. The double-layer baffle uses 8/32 threaded inserts with stainless machine screws included. Rubber feet for downfiring are included. Polyfill is factory-installed. Impedance Options — D2 and D4 The GUS-10 is available as a Dual 2-ohm (D2) and Dual 4-ohm (D4). D2 T/S parameters are not yet finalized by ResoNix — D4 data is published. Wire the D4 parallel for 2 ohms or series for 8 ohms. Wire the D2 parallel for 1 ohm or series for 4 ohms. The D4 wired parallel at 2 ohms into a 2-ohm-stable monoblock delivering 400–500 watts RMS is the practical target for most builds. Confirm your amplifier's stable impedance before selecting the voice coil configuration. Where It Fits At 26" × 14" × 6", this is the most compact GUS enclosure in the Micro Series. The 4.12" driver mounting depth and 6" total enclosure depth open install locations that the GUS-12 cannot reach: Under-seat — compact cars, sport sedans, crossovers Passenger footwell — front sub applications Behind-seat — compact and mid-size truck cabs Trunk corner — compact cars and coupes Side cargo panel — SUVs and crossovers Front subwoofer builds — DSP-controlled SQ and competition systems 2-Year Warranty All Proline X Micro Series enclosures carry a two-year manufacturer's warranty against defects in materials and workmanship. Built and inspected in our Tullahoma, Tennessee facility before shipment. Contact Audio Intensity directly for warranty support. Made in Tennessee Every Proline X Micro Series enclosure is CNC-cut and hand-assembled in Tullahoma, Tennessee on ShopSabre CNC routers. Internal volume, cutout geometry, dado joint depth, baffle layer count, dowel placement, and terminal positioning are all held to spec on every unit. Langboard Elite MDF throughout — named, mill-documented, published density and bond specifications.