EM Test ISO 7637 Automotive Transient System Rental

Overview The EM Test VDS200N, LD200N, UCS200N, & ACC provides a full ISO7637 test solutions and comes with an ISO 17025 accredited calibration. This system is controlled through software through the laptop, which has the required information already installed. . This system is a combination of sevearl different Automotive EMI products providing a complete test system. Each one of the major components can be rented individually, comes with a laptop, and is calibrated to ISO 17025. We offer rentals, as short as a week, providing a cost effective solution for a short term testing need. Data SheetUser ManualRemote Control Manual Specifications VDS200N Common Standards ISO 7637-2 pulses 2b and 4, ISO 16750, GMW3172 and many others Output Voltage 0V – 60V Output Current 0A – 15A, continuous Peak Current 15A Frequency Range DC to 100kHz Supply Voltage 115/230V Weight 49kg (108.02lbs) Dimensions 19”/6HU COMMON DATA (ALL MODELS) Ripple voltage Ur <0.2Vp-p, frequency min. 400Hz Source impedance Zi = <10mohm Sinusoidal signal capability vs. Frequency *) Vpp max. 16V up to 20kHz Vpp max. 10V up to 30kHz Vpp max. 6V up to 50kHz Vpp max. 3V up to 100kHz via Analog In, controlled by AutoWave/AMP 200Nx only VDS 200N30.1 and VDS 200N50.1: Vpp max. 65V resp. 35V up to 50kHz with respect to the selected voltage range Vpp max. 3V up to 100kHz via Analog In, controlled by AutoWave/AMP 200Nx only Fuses Depending on VDS 200N model TRIGGER Automatic Automatic release of the events Manual Manual release of a single pulse External External release of a single pulse OUTPUT DUT Supply +/- Safety laboratory or high current connectors Ext. trigger 5-15V TTL; BNC connector CRO Trigger 5V TTL-signal for oscilloscope TEST ROUTINES FOR ARBITRARY WAVES DC source Max. 60V; current depending on VDS 200N model Functions Sine Wave Sweep Sine Wave (Cranking) Clipped Load Dump Jump Start Extern GM 9105P Pulse 4 Drop and Jump pulse Standard Test routines ISO 7637, Pulses 2b and 4 ISO 16750-2 Jaso Test 1 Service Service, Setup, Self test INTERFACE Serial interfaxe USB Parallel interface IEEE 488, addresses 1 - 30 Remote control To connect an external signal generator (10kohm): 0-10V / 0-50kHz max. 0.5V(p-p) / 0-100kHz LD 200N Common Standards SAE J1455, SAE J1113, ISO 7637 – 5a,5b,7, ISO 16750-2, GMW3172 and many other car manufacturer standards Voltage 20V – 200V ± 10% Built in Coupler 60V/30a Options Clipped Load Dump Waveform 5b ISO 7637 Waveforms 5a and 7 Rise Time 5ms – 10ms (10-90%) Pulse Duration 40-400ms (10-10%) Internal Resistor .5 ohm – 38 ohm, selectable in 0.1 ohm steps Repetition Rage Min. 30s Freestyle Mode Rise Time 10µs – 10ms Pulse Duration 10ms – 1.200 ms Internal Resistor Built in 0.5 – 38ohm , selectable in 0.1 ohm steps Weight 25kg (55lbs) Dimensions 500mm x 450mm x 290mm (19.68 x 17.71 x 11.41) UCS 200N Common Standards SAE J1113, JASO, ISO 7637, GMW3172 Nissan, and many other car manufacturer standards Built in Coupler 80V, up to 50 amps, 100 amps for 500ms ISO 7637 Waveforms 1,2a,3a,3b,6 Burst Tests ISO 7637 waveforms 3a,3b and others Test Voltage 25V – 1000V ± 10% Rise Time 5ns ± 1.5ns Pulse Duration 150ns ± 45ns Source Impedance Zq = 50 ohm Trigger of bursts Automatic, manual, external Burst duration T4 = 0.1ms – 999.9ms Repetition Rate T5 = 10ms – 9,999ms Spike Frequency F = 0.1kHz – 200kHz Test Duration T = 0:01min – 999:59min T > 999:59minàEndless Micropulse Test ISO 7637 waveforms 1,2a,6 and others Test Voltage U = 20V – 600V ± 10% (Peak voltage and polarity as per selected standard) Repetition Rate 0.2s – 99.0s Free Style Rise Time 1us – 10us in steps of 1 us Pulse Duration 50us – 10,000us Internal Resistance 2 ohm – 100 ohm in steps of 5 ohm; 200 ohm, 400 ohm and 450 ohm Weight 20kg (44.09lbs) Dimensions 19”/3HU Packing List/Accessories Included with Rental Below you will find a list of common accessories that you can expect to be delivered with the equipment. This is a generic standard list and should you require an exact connector or accessory please contact us prior to order shipping. The laptop that comes with the battery supply generator also come with ISO control software allowing for a quick, turnkey solution. VDS 200N Battery Simulator/Generator Power Cable USB Interface Cable Printed Manual Calibration Documentation Short Introduction USB Drive with License & Software 125V Plug (2) MC Connector Cable (red & black) (2) Clamps Red & Black Red Shipping Case LD 200N Load Dump Generator Power Cable (4) Safety Lab Cables with Alligator Clips Printed Manual Calibration Documentation Software License Software on USB Stick/Drive (4) MC Connectors Sets USB Cable 9pin serial cable Shipping Case UCS 200N Automotive EFT Generator Power Cable Printed Manual Calibration Documentation Software License (4)Recessed Banana Jack Cords with Clips ISO.control Software on USB Stick USB Cable (4) MC Connectors Pelican Case Video EM Test - Automotive Conducted Immunity Generators Description: This video provides an overview on the EM Test conducted immunity test system. The three major components of this automotive EMC test equipment are the LD 200N, UCS 200N, and VDS 200N. This video provides and overview of these test systems including, ISO 7637-2 waveforms covered, accessories that come with equipment, setup, connecting all equipment, and troubleshooting. It also, provides insight into how to setup the software to allow remote testing to be conducted through laptop. Testimonials I would recommend Transient Specialists. Transient Specialists always provides quality products within the established timeframes. The equipment always meets the specifications and properly shipped within the time frames within the time frames promised. Scott D., TUV SUD Canada Transient Specialists has been outstanding at working with us for our specialized EMC equipment rental needs. Fast shipments and excellent accommodation for some customized setups. I recommend them highly and they are a pleasure to partner with! John H., Gates Air, Inc. Laura, I want to thank you and Goran for your excellent customer service and turn around time on the rentals and the calibration documents. Adam P., Clark Testing Working for a testing company I deal with renting equipment all the time. Transient Specialist is the first company I call on my list of rental houses because of their great personnel, prompt delivery of the equipment, knowledgeable and accommodating to the customers needs. Richard T., National Technical Systems