Vessel 220USB1U e-ASSIST Screwdriver, Higher Torque Model w/ Impact Ball 11-Pc Bit Set & BALL GRIP Ratchet Screwdriver Set

Vessel e-ASSIST Higher Torque Screwdriver w/ Impact Bit Set & Ratchet Driver | Tool Nut Key Features Three Driving Methods in One Kit Pairs a USB-rechargeable e-ASSIST powered screwdriver with a 36-tooth ratchet screwdriver and an impact-rated bit set — powered, manual-ratchet, and impact driving covered without buying three separate tools. 2 Drivers, 21 Bits Total The e-ASSIST driver ships with its own Impact Ball bit, the ratchet screwdriver includes 10 bits in a BITSBELT holder, and the IB11P02U set adds 11 more impact-rated bits — Phillips, slotted, square, and Torx covered. USB-Rechargeable Powered Driver The e-ASSIST screwdriver's built-in 3.6V, 800mAh Li-ion cell charges over any standard USB port — no proprietary dock or disposable batteries for the powered tool in this kit. Overview This bundle pairs the Vessel 220USB1U e-ASSIST Screwdriver, Higher Torque Model with the Vessel IB11P02U Impact Ball 11-Piece Impact Driver Bit Set and the Vessel 2200MBH120K01 BALL GRIP Interchangeable Ratchet Screwdriver — a powered driver, an impact-ready bit set, and a manual ratchet driver together in one kit. Model Numbers: 220USB1U (USB-rechargeable e-ASSIST driver, Higher Torque), IB11P02U (11-piece impact driver bit set in pop-up case), 2200MBH120K01 (36-tooth ratchet screwdriver with 10-bit set). The 220USB1U is a hybrid electric/manual driver: its motor delivers 17.7 lbf-in (2.0 N·m) at 280 rpm no-load speed for fast repetitive tightening, then switches to manual mode for up to 88.5 lbf-in (10 N·m) of hand torque on the final turns — rated for fasteners up to M6. It runs on a built-in 3.6V, 800mAh Li-ion cell that recharges over any USB port via the included micro-USB cable, and it has a built-in LED that lights the fastener as you drive. It ships with a (+)2 Impact Ball Torsion Bit, 90mm. The 2200MBH120K01 is a manual ratcheting screwdriver built around a 36-tooth internal ratchet, so you can keep the bit engaged and drive with short wrist movements instead of full handle resets. Its ball-grip handle detaches to convert the tool into a compact stubby driver for tight clearances, and its SUS bit holder uses a rare-earth magnet to keep bits seated. It includes 10 bits (slotted, Phillips, square, and Torx) in a BITSBELT holder, all on a standard 1/4-inch hex interface. The IB11P02U rounds the kit out with 11 more impact-rated bits in a compact pop-up case — a slotted bit, three Phillips bits, a square bit, five Torx bits, and a 50mm bit holder, all rated at 62 HRC hardness and built with a torsion zone to absorb shock from impact driver use. Together this kit covers three ways of driving a fastener — electric-assist for speed, manual ratchet for feel and tight spots, and impact-rated bits for use in a cordless impact driver — on a shared 1/4-inch hex bit standard. It's a fit for electronics techs, installers, maintenance crews, and any DIYer who wants a complete small-fastener kit without piecing one together themselves. What's in the Box (1) Vessel 220USB1U e-ASSIST Screwdriver, Higher Torque Model (1) Impact Ball Torsion Bit, (+)2 x 90mm (for 220USB1U) (1) USB charging cable, Micro USB Type B, 1m (for 220USB1U) (1) Vessel 2200MBH120K01 BALL GRIP Interchangeable Ratchet Screwdriver (10) 1/4 in. hex shank bits for 2200MBH120K01: Slotted #4, Slotted #6, Phillips #1, Phillips #2, Phillips #3, Square #1, Square #2, Torx T15, Torx T20, Torx T25 (1) BITSBELT bit holder, 6.35mm (for 2200MBH120K01) (1) Vessel IB11P02U Impact Ball 11-Piece Impact Driver Bit Set: Slotted #6, Phillips #1, Phillips #2, Phillips #3, Square #2, Torx T10, Torx T15, Torx T20, Torx T25, Torx T30, plus a BH-2 bit holder (50mm) (1) Pop-up case (for IB11P02U bit set) No case is specified by the manufacturer for the 220USB1U driver itself. Key Specifications e-ASSIST Electric Torque 17.7 lbf-in (2.0 N·m) at 280 rpm e-ASSIST Manual Torque (max) 88.5 lbf-in (10 N·m) e-ASSIST Battery 3.6V, 800mAh Li-ion, USB rechargeable e-ASSIST Max Fastener Size M6 Ratchet Gear (2200MBH120K01) 36-tooth Bit Set Hardness (IB11P02U) 62 HRC Bit Interface (all pieces) 1/4 in. hex shank Total Bits Included 21 (10 on ratchet driver + 11 in IB11P02U set) Made In Japan Compatibility Shared Bit Standard Every bit in this kit — on the ratchet driver, in the IB11P02U set, and the e-ASSIST driver's own bit — uses the standard 1/4 in. (6.35mm) hex shank interface, so bits are interchangeable across all three pieces. Impact Driver Use The IB11P02U bits are torsion-designed and marked for impact driver use; the e-ASSIST and ratchet drivers in this kit are manual/low-torque powered tools, not impact drivers. Built For Electronics Assembly Panel & Enclosure Work Furniture Assembly Small Appliance Repair General Repair Maintenance Installation Work Bench Work Pro Tip Reach for the e-ASSIST driver for repetitive small fasteners, the ratchet screwdriver when you need feel and tight-space access (detach the handle for stubby mode), and swap in the IB11P02U bits whenever the job moves to a cordless impact driver — all three pieces share the same 1/4 in. bit standard, so there's no bit-swapping headache between them. Warranty & Support Vessel covers its e-ASSIST series products — which includes the 220USB1U — under a 6-month warranty, requiring proof of purchase through an authorized dealer. The 2200MBH120K01 ratchet screwdriver and IB11P02U bit set are manual hand-tool accessories with no separate warranty term stated by Vessel. Tool Nut's Take Tool Nut's Take A Complete Small-Fastener Kit — Powered, Ratchet, and Impact Instead of picking one driving method, this bundle gives you all three in a shared bit standard, so whatever the job calls for, you've already got the right tool in hand. Who it's for: Electronics techs, installers, maintenance crews, and DIYers who want a powered driver, a manual ratchet driver, and an impact-ready bit set together instead of assembling one piecemeal. Why it stands out: All three pieces share a 1/4 in. hex bit interface, so the 21 included bits work across the ratchet driver, the e-ASSIST driver, and any compatible impact driver you already own. Worth knowing: The e-ASSIST driver's electric assist tops out at M6 fasteners and 2.0 N·m — it's built for repetitive small-fastener speed, not as a substitute for a cordless drill/driver or impact wrench on larger fasteners; the ratchet driver and IB11P02U bits are manual/impact accessories, not electric tools. Common Questions Do all the bits in this kit fit each other's tools? Yes — the e-ASSIST driver, the ratchet screwdriver, and the IB11P02U set all use the standard 1/4 in. (6.35mm) hex shank interface. Can I use the IB11P02U bits in a cordless impact driver? Yes, they're torsion-designed and marked for impact driver use. The e-ASSIST and ratchet drivers included in this kit are not impact drivers themselves. Does the e-ASSIST driver need a separate charger? No — it charges over any standard USB port using the included micro-USB cable. What's the difference between this kit and the VesselBundle-Speed kit? This kit includes the 220USB1U Higher Torque e-ASSIST driver; VesselBundle-Speed swaps in the 220USBS1U Higher-Speed e-ASSIST driver instead. The ratchet screwdriver and bit set are the same in both.