0AM927769G TCU DSG 7 DQ200 Temic Remanufactured

Temic Remanufactured TCU 0AM927769G DSG 7 DQ200 0CW Part Number: 0AM927769G Original Temic remanufactured transmission control unit for 7-speed DSG DQ200 / 0CW dry clutch systems Transmission Type DSG 7 DQ200 / 0CW Condition Remanufactured Manufacturer Temic Component Transmission Control Unit (TCU) Clutch Type Dry Clutch Programming Required Tested & Remanufactured Temic TCU This remanufactured 0AM927769G unit is an original Temic transmission control module for selected DSG 7 DQ200 / 0CW mechatronics systems. Public listings identify this part number specifically as a Temic DQ200 TCU requiring programming and cloning after installation. OEM Part Numbers Main OEM Number: 0AM927769G Related Temic References: 0AM927769D • 0AM927769K • 0AM927769F • 0AM927769E Compatible Mechatronics Codes: 0AM325025D • 0AM325025H • 0AM325025J • 0AM325065N • 0AM325065L • 0AM325065S • 0AM325065T • 0AM325065AB Always Verify Your Part Number Before ordering, compare the OEM number on your original TCU and confirm it matches 0AM927769G. As with other DQ200 Temic units, correct hardware and software matching is essential for proper operation. Technical Specifications Transmission Type: 7-Speed DSG DQ200 / 0CW System Codes: 0AM / 0CW Component: Transmission Control Unit (TCU) Manufacturer: Temic OEM Number: 0AM927769G Related References: 0AM927769D / 0AM927769K / 0AM927769F / 0AM927769E Clutch Type: Dry Dual Clutch Condition: Remanufactured Temic Unit Programming: Cloning / programming required after installation Application: VW Audi Skoda Seat DQ200 vehicles Product Description This remanufactured 0AM927769G transmission control unit is an original Temic module for selected DSG 7 DQ200 / 0CW mechatronics systems with dry clutch. It serves as a replacement for defective or non-communicating original TCUs in compatible VW Group vehicles. What This TCU Does Controls electronic functions of the DQ200 mechatronics system Processes sensor inputs and manages transmission logic Supports shift strategy and gear engagement control Works together with the hydraulic section of the mechatronics assembly Serves as a replacement for faulty original Temic TCU units Important Programming Note This unit is not plug-and-play and requires programming or cloning from the original module. Public references for 0AM927769G explicitly state that a clone tool or appropriate programming procedure is necessary before the TCU can operate correctly in the vehicle. Vehicle Compatibility The 0AM927769G TCU is used in selected Volkswagen Group vehicles with 7-speed DSG DQ200 / 0CW transmission and dry clutch system. Public application lists for this part number include Volkswagen, Audi, Škoda and SEAT models. Suitable for Selected Models Such As Audi A3 (2013 - 2016) Audi A3 Cabriolet (2015 - 2016) Audi Q2 Audi TT Volkswagen Golf (2013 - 2017) Volkswagen Golf Sportsvan (2014 - 2019) Volkswagen Jetta Volkswagen Passat Volkswagen Polo Volkswagen Scirocco Volkswagen Touran Volkswagen T-Roc Škoda Octavia (2013 - 2017) Škoda Rapid Škoda Fabia Škoda Yeti Škoda Karoq SEAT Leon (2013 - 2016) SEAT Altea SEAT Toledo Compatibility Check Recommended DQ200 applications can differ according to software version, mechatronics configuration and vehicle production details. If you are not sure, send us your VIN number and the part number from your original module for verification before ordering. Common Fault Codes & Symptoms A failing DQ200 TCU can cause communication problems, gear selection faults, loss of drive or transmission emergency mode. Public DQ200 repair sources also note various CAN communication complaints and gearbox control problems when the Temic control electronics fail. No communication with transmission control unit Diagnostic tools cannot communicate with the gearbox electronics CAN communication faults Other control units report missing communication with the transmission module Gear selection malfunction Incorrect shifting or failure to select gears Limp mode Gearbox switches to emergency operation Hydraulic control fault Valve body or pressure regulation related malfunction Harsh or delayed shifting behaviour Warning message for gearbox malfunction on dashboard Intermittent or permanent transmission operating issues Diagnostic Tip Because DQ200 issues may involve electronics, hydraulics, clutch wear or software mismatch, proper diagnosis should always be carried out before replacement. Matching only by gearbox code is not always enough; public technical guidance emphasizes verifying the hardware version of the TCM. Installation & Service Notes Recommended Steps Verify the exact OEM number on the original control unit Confirm the gearbox is a DSG 7 DQ200 / 0CW version Inspect the mechatronics assembly for related electrical or hydraulic damage Clone the original unit or load the correct software where required Install the module carefully using professional workshop procedures Perform diagnostic checks, fault code clearing and adaptation after installation Verify gearbox operation during test drive after repair Important Installation Note This product is an electronic transmission component. Incorrect programming, mismatched software or improper installation can prevent the gearbox from operating correctly. Installation by a DSG specialist is strongly recommended. Why TCU Replacement Matters 1. Restores Communication A healthy control unit is essential for communication between the gearbox mechatronics, sensors and vehicle systems. 2. Supports Correct Shifting The TCU manages transmission logic and helps maintain proper gear selection and clutch operation. 3. Prevents Repeat Faults When a defective module is correctly replaced and programmed, recurring control-related transmission faults can be eliminated. 4. Improves Reliability A tested replacement unit helps restore dependable DSG operation when the original electronics have failed. Quality Assurance & Warranty This remanufactured original Temic part is tested before dispatch to confirm proper basic functionality. Because this is an electronic transmission component, final operation always depends on correct installation, matching software and overall gearbox condition. Quality Control Includes: Verification that the unit is an original OEM-type component Functional testing before shipping Visual inspection of connector and housing condition Basic identification and part number check Warranty Does Not Cover: Damage caused by incorrect installation Software mismatch or failed programming Hydraulic or mechanical gearbox faults unrelated to the TCU Electrical damage caused by wiring or voltage problems in the vehicle Questions or Need Help? Our technical team is ready to assist with compatibility checks, software questions and product selection. Contact Important Purchase Information Please compare the OEM number on your original unit before purchase This is a remanufactured electronic transmission control unit Programming, cloning or adaptation is required Professional installation is recommended Photos are for illustrative purposes only Worldwide shipping is available If your country is not listed at checkout, contact us for manual order processing Please check carefully whether this product matches your vehicle and gearbox version before ordering