Ceramic Pro — Inductor Tank System

Load 250 lbs. Blast Until the Job’s Done. The complete, high-capacity gravity-fed sandblasting system — a rigid full-drain cone tank on a purpose-built stand, paired with the versatile Ceramic Series for full frames, full shells, restoration work, and the jobs you get paid for. If you’re pricing out a pressure pot just to get more run time out of your rig — stop. The Inductor Tank + Stand runs the same patent-pending metering sleeve valve and air assist system that made the gravity-fed delivery system work, scaled up and built solid. A rigid roto-molded cone tank sitting on a dedicated steel stand, holding up to 250 lbs of media in a single fill. The included Ceramic Series completes the system, turning the pressure washer you already own into a controlled wet-sandblasting setup for removing rust, paint, varnish, and corrosion from metal, concrete, brick, wood, vehicles, trailers, frames, and equipment. Pour it in. Dial it in. Work. Ceramic Series included · Up to 250 lbs per fill · Rigid full-drain cone · Dedicated heavy-duty stand · Sealed vented lid · Works with 1,500–5,000 PSI pressure washers · No compressor required · Engineered in the USA WHY THE TANK ✓ Up to 250 lbs in one fill. Fifteen gallons of dry media, depending on what you’re running. That’s a full side of a car, or a complete frame, without walking back to the shop. On the BMW 2002 shell, the whole job ran fifteen 90 lb bags — this is how you feed a job that size without your day turning into refills. ✓ Rigid. Nothing flexes, nothing sags, nothing shifts. Roto-molded polyethylene, one solid piece, no seams to split. Load it to the top and the geometry doesn’t change — the tank holds its shape and the valve holds its position from the first pound to the last. Set your flow once and it stays where you set it. ✓ Full-drain 54° cone — it actually empties. This is the same cone design farms use to mix and dump chemical in the field, engineered so nothing settles in a corner and nothing bridges. Media keeps falling straight down into the metering sleeve valve until the tank is genuinely empty. You blast what you paid for instead of leaving a wedge of it stuck in the bottom. ✓ Solid on the ground. The tank drops into a dedicated stand built 4” taller than standard specifically to clear the full-drain cone — so the valve sits at working height and the media hose runs straight out with nothing in its way. A 20” × 20” footprint and a loaded tank sitting low and centered. Shop floor, gravel, dirt, grass. Set it down and it stays put. ✓ Built for the long haul. Polyethylene doesn’t rust, doesn’t rot, and doesn’t care about weather. UV-inhibited for life outdoors. This is equipment built to sit in a yard, get loaded and unloaded a hundred times, and still be the same tank in five years. ✓ Sealed vented lid — 12” threaded. Load it and leave it. Rain, dust, and shop debris stay out, and your media stays dry. Wet media is the number one cause of a slow feed, and a sealed lid is how you never deal with it. ✓ See your level without stopping. Translucent tank with gallon markings molded in. Glance over mid-job and know exactly what you’ve got left, so you top off on your terms instead of finding out at the worst possible moment. ✓ Doesn’t clog. Media falls straight down through the patent-pending metering sleeve valve into the air assist system. No pickup tube to jam. Nothing to shake. ✓ Make it part of the rig. Bolt it to a trailer, a cart, or a shop corner and it becomes a permanent blasting station — a fixed piece of your setup instead of something you assemble at the start of every job. ✓ Ceramic Series included. The system comes with the Ceramic Series for controlled, versatile wet blasting across metal, concrete, brick, wood, vehicles, trailers, frames, and equipment. The nozzle system remains interchangeable, so you can upgrade to the Carbide 600 when the job calls for it. WHY THE CERAMIC SERIES ✓ Built for the whole job list. Remove rust, paint, varnish, and corrosion from trailers, cars, trucks, frames, tractors, farm equipment, auto parts, boats, concrete, brick, and wood. ✓ Works with the pressure washer you already own. Compatible with electric and gas pressure washers from 1,500–5,000 PSI, covering lighter cleaning through tougher rust and paint removal. ✓ Control the pressure for the surface. Run higher pressure for heavy rust on steel and equipment, or reduce it for paint, wood, brick, concrete, and more delicate surfaces. ✓ No compressor or blasting cabinet needed. Water force from your pressure washer carries the abrasive media to the surface, giving you a practical wet-blasting setup without the cost and footprint of industrial equipment. ✓ Easy to control and adjust. The tank meters the media, the air assist keeps it moving, and the Ceramic Series gives you a steady, repeatable blast at the surface. ✓ Match the media to the job. Use coarse media such as Black Diamond or glass beads for rust and paint. Use softer media such as soda or walnut shell for wood and more delicate surfaces. ✓ Replaceable nozzle system. Ceramic nozzles are wear items. When a nozzle reaches the end of its service life, swap it and keep working instead of replacing the complete system. THE MECHANISM Your pressure washer does the work. No compressor, no pressure pot, no cabinet, no dust containment plan. The patent-pending metering sleeve valve sits at the bottom of the cone. Quarter turn to open — it locks in and holds. Below it, the air assist system mixes air into the media before it ever reaches the Ceramic Series. That’s why the stream comes out continuous instead of surging. Feeds abrasive media downward naturally — like an hourglass — so your washer only needs a little pull to maintain a perfect, steady feed. No sputtering, no clogs, no shaking a bucket. 6-hour job. 5 minutes of downtime. Full 1972 BMW 2002 shell — roof to rockers, heavy Bondo on a door and two quarter panels. Total downtime across the entire day was five minutes, and that was one fitting change. No clogs. No flow interruptions. BUILT FOR BIG JOBS Full car shells and full frames — measured in hours, not minutes Farm and heavy equipment — implements, decks, loaders, gates, tanks Trailers, tube frames, dune buggies, truck beds Anyone blasting for money — uninterrupted run time is margin Shop rigs and trailer builds — a permanent station, not a setup you rebuild every time Concrete, graffiti, large metal panels, marine work Brick, wood, furniture, fences, patios, and restoration projects PRESSURE GUIDE FOR DIFFERENT JOBS Removing rust 3,000–5,000 PSI Tough rust on tractors, farm equipment, frames, and vehicles Stripping paint 2,500–4,000 PSI Cars, trailers, boats, panels, and other painted surfaces Dirt, grime, and mold 1,500–2,500 PSI Brick, concrete, patios, and wood Varnish removal 2,000–3,500 PSI Wooden surfaces and furniture DIALING IT IN — WHAT “RIGHT” LOOKS LIKE Have a test spot ready. Scrap panel, or just the concrete. Watch the media hose. If you’ve ever seen sand run through the narrow point of an hourglass — smooth, continuous, no surging — that’s what you want to see. On a sunny day you can see it right through the line. At the Ceramic Series, the stream should still look like water, with the media carried inside it. Judge the rest by feel: the ricochet coming back should be a light ping of fine grains, barely felt. Too much media and it bounces back like mini ping-pong balls. Not enough and you’re just spraying water. Sit just under “too much.” Hose moving like a worm? Flow surging? Too much sand, not enough air. Back the meter off one full turn. Dial to what you’re removing. Light paint needs far less media than heavy Bondo. Don’t waste sand. RUN IT LIKE A PRO Startup: Water first, always. Trigger pulled and water flowing before the valve opens. Shutdown: Close the meter first, let the hose evacuate, then stop. Reopen the meter to restart. Two seconds of discipline. It’s what keeps the next pull clean instead of clogged. HOW IT RUNS Set the stand on level ground and drop the tank in. Pour your dry media straight in through the 12” opening — no funnel, dump it from the bag. Connect the Ceramic Series nozzle assembly to your compatible pressure-washer gun or wand. Connect the reinforced media hose to the Ceramic Series nozzle assembly. Open the air inlet so the media feeds smoothly. Trigger and water first. Quarter turn on the sleeve valve — dial it in on your test spot. Blast until the job’s done. WHAT MEDIA SHOULD I USE? Black Diamond / Coal slag Heavy rust, paint, and demanding steel surfaces Crushed glass / Glass beads Rust, paint, corrosion, and general surface preparation Garnet Steel, vehicles, frames, and restoration work Soda Lighter cleaning and more delicate surfaces Walnut shell Wood and delicate restoration work Always keep your media dry. Wet or clumped media is the most common cause of poor feeding. Sift reclaimed media through a stainless screen before putting it back in the tank. SPECS System Inductor Tank + Dedicated Stand + Ceramic Series Capacity 15 gallons — up to 250 lbs of media, depending on media type Tank Roto-molded polyethylene, one-piece, translucent with gallon markings Cone 54° full-drain Tank dimensions 19” dia. × 27” H Stand dimensions 20” × 20” × 33” H Stand height 4” taller than standard, for full-drain cone clearance Lid 12” threaded vented lid Metering Patent-pending metering sleeve valve Air Air assist system Nozzle system Ceramic Series included Pressure-washer range 1,500–5,000 PSI Pressure washer Electric and gas Surface compatibility Metal, concrete, brick, wood, vehicles, trailers, frames, boats, and equipment Compressor required None Media Crushed glass, glass beads, garnet, coal slag, soda, walnut shell, and other suitable dry blasting media Outdoor rating UV-inhibited Engineering Designed and engineered in the USA WHAT’S IN THE BOX 1× 15-Gallon Full-Drain Inductor Tank 1× Dedicated Tank Stand 1× Ceramic Series Wet-Sandblasting Nozzle Assembly 1× Ceramic Nozzle Set 1× Pressure-Washer Connection Adapter 1× Patent-Pending Metering Sleeve Valve Assembly 1× Air Assist Inlet Section 1× Reinforced Media Hose 1× Step-by-Step Setup Guide FAQ How much media does it hold? Fifteen gallons — up to 250 lbs depending on what you’re running. Denser media weighs more per gallon. Does it include the Ceramic Series? Yes. This is the complete Inductor Tank + Stand + Ceramic Series system. The Ceramic Series nozzle assembly, ceramic nozzles, and pressure-washer connection adapter are included. Will it work with my pressure washer? The Ceramic Series works with compatible electric or gas pressure washers from 1,500–5,000 PSI. Match the pressure to the surface and the job, and contact support with your machine’s PSI and GPM if you’re unsure. Which should I get — the tank or the bag? Both run the same patent-pending metering sleeve valve and the same air assist system, so the blasting feels identical. The tank is the heavy-duty end of the line: more capacity per fill, a rigid full-drain cone, a sealed lid, and a build meant to live outdoors and get used hard for years. If you’re running full shells and frames or you want a permanent station on your rig, this is the one. Do I need to bolt it down? No. Loaded, it isn’t going anywhere. Bolt it to a trailer or cart if you want the whole rig to travel as one unit. Can I leave media loaded in it? Yes — that’s what the vented lid is for. Keep it dry and it’s ready to go next time. What media should I run? Use coarse media such as Black Diamond or glass beads for paint and rust. Use softer media such as soda or walnut shell for wood and more delicate surfaces. Keep every media type dry and sift it before loading. Can I use it on concrete, brick, or wood? Yes. Match the pressure and media to the surface. Use lower pressure and milder media for wood and delicate surfaces, keep the nozzle moving, and test an inconspicuous area first. Can I use it on boats? Yes, with care. Start with reduced pressure and a milder abrasive, keep the nozzle moving, and test an inconspicuous area first—especially on fiberglass. How long do the ceramic nozzles last? Ceramic nozzles are wear items, and service life depends on abrasive type, grit, PSI, and usage. Inspect them regularly and keep replacements available for larger projects. Does it come with the stand? Yes. Tank, stand, and Ceramic Series ship together as one complete system. Fill it once. Finish the job. 30-day money-back guarantee. Real support for setup, media, and pressure-washer questions. Replacement ceramic nozzles always in stock. Complete system: Ceramic Series + Inductor Tank + Stand — controlled, high-capacity gravity-fed wet blasting in one package. Add-ons: Sand filter / sifter · Rust converter–inhibitor · AP1 conversion coating · Replacement ceramic nozzles · Carbide 600 upgrade