In Stock ! Maytech GPS Remote Controller MTSKR26WF V5.0 – IP68 Waterproof Wirless Hand Controller with GPS Tracking & Tilt Protection for Efoil ESurf ESK8

Maytech GPS Remote Controller MTSKR26WF V5.0 – IP68 Waterproof Wirless Hand Controller with GPS Tracking & Tilt Protection for Efoil ESurf ESK8 (Updated version of V3) Model No MTSKR26WF V5.0 Upgraded Function Equipped with GPS (GPS Speed, Distance, Max Speed, Average Speed) Equipped with Tilted protection (IMU tilt sensor), protection angle can be adjusted to 30°/45°/60° tilt degree of your board in case of flipping over, separation of the rider from the board, or an accidental fall. IMU degree can be calibrated according to the receiver position to be placed on your board. Tilt protection can be turned off for experienced users. Waterproof Rank IP68 Waterproof with 2 Layers Nanometers Coating, both on PCB board and screen Thr Mode Esurfboard (SF) , with cruise control and ESK8 (SK), can control forward and reverse when use on marine applications 3 Speed Modes With, adjust throttle % from 20-100%, friendly for beginners Power Modes 2 levels, Eco (Level 1) & Pro (Level 2) optional Signal strength: Pro ＞ ECO Power Consumption: PRO ＞ ECO Throttle Lock Yes, 10-120s optional Signal Format Support Standard PWM (PPM) and UART, output range from 10%-20%, which correspond to ESC/VESCTOOL Compatible controller throttle output range from 0%-100%. PWM Signal Output Range In Esk8 (SK) mode: 1.5ms is stop position, 1.5-1ms for brake or reverse (upper trigger), 1.5-2ms for throttle (bottom trigger) In Esurf (SF) mode: 1-2ms for throttle (bottom trigger), no brake or reverse Double Source Power Supply Accept 5V power by ESC built-in BEC or extra 5V power Output Signal Max 3.3V Display Parameters GPS Speed / Distance / Max Speed / Average Speed Tilt sensor angle RPM+Current+Voltage+Temp(When work with VESC and MTSF-WP32 series ESCs) Signal strength, remote and battery power bars, battery voltage%, RPM, speed (km/miles), with VESC, Maytech WP32 ESC and other ESCs Receiver built-in switch 20V 2A Mosfet Switch (transistor switch); No Relay Switch for this version Cruise Control With in SF Mode (Esuf) Brake or Reverse With in SK Mode (Esk8) Accessories Wirelss charging pad / Receiver / USB cable / Wristband / 1pcs 3 pins cable / 1pcs UART cable Compatible Controllers VESC/ Focbox/ Other PWM ESCs that has same signal output range with the remote. Application foil assist system, electric propulsion, underwater thruster, electric outboard, Esurf, Efoil, electric hydrofoil, electric surfboard, electric skateboard/ elongboard/ mountainboard, electric paraglider, etc., Please refer to MTSKR1905WF V3.0/V3.1 Video first: >Download Manual: Maytech MTSKR26WF V5.0 Waterproof Remote Control User Manual Functions: ● Equipped with GPS (GPS Speed / Distance / Max Speed / Average Speed) ● Equipped with Tilted protection (IMU tilt sensor), protection angle can be adjusted to 30°/45°/60° tilt degree of your board in case of flipping over, separation of the rider from the board, or an accidental fall. IMU degree can be calibrated according to the receiver position to be placed on your board. And Tilt protection can be turned off for experienced users. ● with 3 adjustable speed modes; ● with throttle lock function for safety; ● with Eco and Pro modes for different signal strength; ● compatible to Maytech new 32bit MTSF160A-WP32 / MTSF300A-WP32 / MTSF300A-WP32-HV / MTSF300A-WP32-HVPRO ESCs to read current/votlage/rpm/temperature datas, etc; ● add a page to display main battery voltage percentage; ● This version contains functions of old firmware versions MTSKSR1905WF V3.0 (excluding the built-in relay switch) ● Waterproof function: Two layers of nanometer-coating are added to remote PCB and Screen, and they're also double protected by waterproof glue. Screen Display for different Data Source and Throttle Mode: Wiring Digram for different Data Source Option: If you use MTSF160A-WP32/ MTSF300A-WP32 60V / MTSF300A-WP32-HV 75V / MTSF300A-WP32-HVPRO 85V ESC, please refer to below wiring diagram: If you use VESC controllers based on V4.12 / V6 / V75_300, please refer to below wiring diagram: For Other ESCs: Using Notice: 1. Wash the remote in freshwater after using in salt water. 2. The remote PCB and screen are sealed by waterproof nano-coating and double protected by glue. The remote case is not sealed, when use it in water, water will get in remmote case. It won't influence using. When you don't use it, please put it in dry place and it will dry slowly. 3. When charge the remote, please keep remote dry. 4. Receiver is not waterproof. Please put receiver in dry place. 5. Because each customer using situation is different, some customers may need replace the antenna with longer one . If you mount the reciever deep in your board, recommend to change to a long 2.4ghz antenna and lead the antena near to your top cover of your board for better signal. 6. When soldering, please pay attention that the two pins do not touch each other, otherwise it is easy to burn the receiver. 7. The extended antenna 1m and 3m PCBs are not waterproof. Related Products: Esk8 Products: Brushless Motors, VESC, Truck, Wheels, etc., Esurf Products: Waterproof Motors, ESC, Propeller, etc.,