The Yeoman Handle

Description The Yeoman Handle is an aftermarket auxiliary grip that clamps onto the shaft of your existing string trimmer, weed eater, or weed wacker. It adds a second grip point higher up the shaft, so both hands work together at chest height instead of one hand fighting the engine and the other twisted across your body. The result is a trimmer you can run upright, with both hands sharing the load, for a full yard without bending or bracing. What’s in the box: Yeoman Handle (16.5″, aluminum-alloy shaft, soft-touch rubber grip, 1.65 lbs), Hold-Fast Bracket (fits 26mm + 28mm shafts), allen key. Three-minute install — no drilling, no zip ties. The Plumb-Se — How It Saves Your Back Plumb is a carpenter’s word. It means dead-vertical — the exact line a weighted string hangs from a beam. The Plumb-Set is our fixed grip angle, locked at the geometry that keeps your spine on that line while you trim. The off-hand grip sits 9 inches above the factory loop, with a 7° forward sweep — the exact height where your arm relaxes at chest level and your shoulder drops out of the lift. Both hands share the trimmer’s weight evenly. Your spine stays plumb. Most aftermarket handles bolt on at whatever angle is convenient and let the customer figure out the rest. The Plumb-Set is fixed at the geometry that works, so your body doesn’t have to compensate for a design that didn’t account for it. The Hold-Fas — Why It Doesn’t Slip The Hold-Fas is our reinforced steel bracket clamp. We took the name from the centuries-old blacksmith’s holdfast — a forge tool that pinned work to an anvil with a single tap, then held it through hammer-strikes hour after hour. Same idea here: tap it tight once, and it holds. The clamp uses a dual-contact pad that grips the shaft on two opposite faces simultaneously. One bolt, two clamp positions: 26mm and 28mm. The dual-contact design distributes pressure evenly so the clamp doesn’t fatigue under the torque of a running trimmer. What that means in practice: you tighten it once with the included allen key, and it stays. No re-tightening between sessions. No slipping when you hit thick brush. No backed-off bolts mid-yard. Will It Fit My Trimmer? The Hold-Fast fits 26mm and 28mm shafts — the standard range for commercial and residential trimmers. That includes most STIHL, Echo, Husqvarna, Ryobi, Greenworks, EGO, and BLACK+DECKER models, gas or battery. If your trimmer has a straight or curved shaft and a loop handle, this fits. If you’re unsure about your specific model, message us before you order — we’ll confirm compatibility in under an hour. Stand Up Straight. Finish In One Pass. You bought a decent trimmer. Twenty minutes in, your back is locked, your shoulder is hot, and Saturday is a write-off. It’s not the engine. It’s the position the factory handle forces you into. The Yeoman fixes that with The Plumb-Set — our fixed grip angle that places your off-hand 9 inches above the factory loop, at chest height. Plumb, in old carpenter’s English, means dead-vertical. That’s what your spine does when this handle is on the shaft. The yard still gets trimmed. You just stand up the whole time — the kind of upgrade nobody thinks to ask for, until they use one. Built To Outlast The Trimmer It Bolts To Most aftermarket clamps are thin stamped steel. They flex under torque and slip after a few sessions. The Yeoman ships with The Hold-Fast — reinforced steel with a dual-contact pad that grips the shaft on two opposite faces. Fits 26mm and 28mm. Tighten once with the allen key; it holds fast through the season. This is the part the factory left off. The Field & Harvest Guarantee Bolt The Yeoman onto your trimmer. Take it through a full Saturday — front yard, fence line, around the shed. If your back doesn’t feel the difference, if you’re not finishing the job in one pass instead of three, return it for a full refund. Sixty days. No restocking fee. Whether it’s for your weekend or someone else’s — the return covers it either way.