OEM Trane MOT12615 | Variable Speed Blower Motor Module Set | 3/4 HP

OEM Trane MOT12615 Is A ECM Blower Motor and Module Set, 3/4 HP Multi-Volt The Trane MOT12615 is an authentic factory-programmed OEM variable-speed ECM blower motor and control module assembly. This high-efficiency direct-drive indoor blower assembly is engineered explicitly for the strict operational demands of premium Trane and American Standard residential air handlers and multi-zone heating systems. Operating dynamically up to 1050 RPM, this permanent magnet brushless motor communicates seamlessly with the main system motherboard to self-adjust its torque output. By altering airflow performance profiles to instantly match fluctuating static duct pressure variables, it establishes optimized environmental climate balancing while dropping structural seasonal electrical operating overhead. Key Features Genuine OEM Certified Matrix: Engineered by Trane Technologies as a factory-direct indoor blower solution, ensuring precise belly-band structural mounting positioning and exact alignment inside the blower housing deck. Pre-Programmed Plug-and-Play Architecture: Arrives pre-loaded with specialized system-specific variable speed micro-logic directly from the factory, enabling immediate high-efficiency system integration without requiring field firmware flashing. Resolves Bearing and Hub Noise: Formulated with an upgraded internal bearing geometry and a balanced rotor designed to permanently fix high-pitched vibrations, shaft binding, and harmonic cabinet hums. Advanced Electrical Surge Protection: Incorporates an isolated internal circuit topology with built-in surge suppression inside the integrated control module to shield the digital microprocessor from fluctuating field line voltage. Product Details Brand: Trane / American Standard Manufacturer: Genteq / Regal Rexnord Part Number: MOT12615 UPC/SKU: 723223126155 / MOT12615-OEM Component Type: Variable Speed ECM Motor & Module Set Output Power / Rating: 3/4 HP (0.75 Horsepower) Operating Voltage: 115V / 208-230 VAC Auto-Sensing Input (Also rated 120/240V) Full Load Amperage (FLA): 9.6 Amps @ 115V | 4.8 Amps @ 230V Frequency / Speed: 60/50 Hz | Variable up to 1050 RPM Frame Size: NEMA 48 Frame (5-5/8 Inch Body Diameter) Phase Configuration: Single Phase (1PH) Enclosure / Profile: Open Air Over (OAO) / TEFC Variant Rotation Direction: Reversible / Auto-Configured Shaft Parameters: 1/2 Inch Diameter | 4-1/4 Inches Long 🛠️ HVAC Depot Pro Tip Take a Picture First! Before decoupling the wiring leads from the failed component, photograph the exact positions of all low-voltage control lines and the line-voltage power taps. Disconnect the main branch circuit power supply and discharge any remaining stored capacitive electrical charges within the motor module before handling. When sliding the new assembly into place on the mounting tracks, verify that the wiring harness routes into a proper downward-sloping drip loop; this forces condensation runoff to roll harmlessly off the wire jackets instead of leaking straight into the sensitive control socket. Cross-Reference Factory Manufacturing Blueprint Code: D341314P72 Genteq Factory Model Platform: 5SME39SL Series / ECM 2.3 Alternative Engineering Reference: D344717P72 Associated Module Configurations: MOD01574, MOD02275 Model Compatibility 4TEE3F (Suffixes: 48A1000AA, 48B1000AA, 49C1000AA, 66A1000AA, 65B1000AA) TUD2 (Suffixes: TUD2C080A9V4VBA, TUD2C100A9V5VBA, TUD2C100A9V5VCA) AUD2 (Suffixes: AUD2C080A9V4VBA, AUD2C100A9V5VBA, AUD2C100A9V5VCA) TAM7 (Suffixes: A0A24H21SBA, A0A30H21SBA, A0A36H31SBA