0.75 x 0.5 x 0.7m Clone Tent — Propagation Tent by seaHawk

The seaHawk Clone Tent is a bench-top propagation room — 0.75 x 0.5 x 0.7m of fully lightproof, ducted, climate-controllable space for cuttings and seedlings. It fits on a bench or in a cupboard, holds two standard propagation trays side by side, and gives clones the sealed dark humid environment they actually need instead of a plastic dome on a windowsill. Push-fit steel frame, waterproof floor tray, and real 150mm ducting ports, so you can run proper extraction in a space this small. Fits Two Prop TraysThe 75 x 50cm floor takes two standard 350 x 295mm trays side by side, or one large tray — Prop 64, Jumbo Clone or Super Dome all drop straight in. Real Ducted Ventilation175mm sleeves in the roof and left wall take 150mm ducting, so you can run a proper inline fan instead of cracking a dome lid and hoping. Seals In Heat and CO²A closed box holds the warmth off your heat mat and any CO² you add, instead of bleeding it into the room. Run it sealed with a CO² pad and the environment does the work. 100% Lightproof ADF LiningA sealed light-tight shell with seaHawk's diamond-structure ADF reflective lining — keeps stray light out of the dark cycle and bounces back what you put in. Specifications Assembled size: 75 x 50 x 70cm Imperial size: 29.5 x 19.7 x 27.6in Floor area: 0.375m² Item code: 4418 Frame: Metal poles, 8 plastic corner connectors Weight: 4.2kg (5.2kg packed) Carton size: 80 x 24 x 13cm Warranty: 12 months (zips 3 months) Roof vent: 1 x 175mm sleeve (fits 150mm duct) Intake port: 1 x 175mm sleeve, left wall (fits 150mm duct) Passive vents: 2 (left and right walls) Cable ports: 2 x 100mm (rear and right wall) Door: Full-width zip with viewing window Hanging bars: 1 shallow (50cm), 2 deep (75cm) Floor: Waterproof zip-in tray, nylon straps Lining: 100% lightproof ADF reflective material Assembly: Tool-free push-fit Distributed by: Holland Forge, Australia Grower's Tip A clone tent needs barely any air. Run your inline on the lowest speed it will hold, or put it on a controller — pull too hard and you will dry cuttings out before they ever throw a root. Because this tent runs happily sealed, a GreenPad Junior is the easiest CO² win there is — no tank, no regulator, no fan. It sits inside, releases CO² as it dries, and helps hold the heat in while it does. Hold humidity around 80-90% for the first week. A small humidifier and a heat mat under the tray will do more for your strike rate than anything else you put in here. Start the light on the shallow bar and move to a deep bar as the cuttings stretch. 26-42W of LED is plenty in a space this size — more just cooks them. Run the heat mat lead, humidifier cord and light cable through separate cable ports. Two 100mm ports means you never have to fight one fat bundle every time you open the door. Check for light leaks with the room dark before your first cycle. If the frame is not pushed fully home the seams sit open and light gets in. Setting Up Your Clone Tent 1Push the frame together by hand — poles into the corners and connectors. Make sure every pole is seated fully home, tapping with a rubber mallet if needed. A loose frame stretches the seams and leaks light. 2Unzip the cover completely, then drop the roof section over all four top corners and settle it square and snug. 3Hang the shallow and deep bars now, before the base goes on. Doing it later means wrestling them through a zipped door. 4Slide the base of the cover under the frame and work it neatly around each corner, then close the zips — pushing the uprights inward as you go around. 5Fit the waterproof floor tray and secure the nylon straps, zip the front closed, then kill the room lights and check for leaks before you load it. Pairs Well With Propagation GearTrays, domes, plugs and cloning gel — everything that goes inside the tent. Heating & Heat MatsRoot-zone warmth is the single biggest lever on strike rate. A thermostat mat under the tray does the work. Humidity ControlCuttings have no roots to drink with. A small humidifier holds the 80-90% they need to survive week one. Grow LightsA 26-42W LED bar on the hanging rails is the right amount of light for a tent this size. GreenPad CO² GeneratorA Junior pad hangs inside and releases CO² as it dries. No tank, no regulator — made for sealed spaces exactly this size. Grow Tent AccessoriesDucting, hangers, clips and the odds and ends that finish off a tent build. Frequently Asked Questions What size propagation trays fit inside?The floor is 75 x 50cm, so two standard 350 x 295mm propagation trays sit side by side with room to spare. If you would rather run one big tray, a Prop 64 (555 x 355mm), Jumbo Clone (530 x 320mm) or Super Dome (530 x 270mm) all fit comfortably. Do I need an extraction fan on a tent this small?Not always. Many growers run the clone tent sealed with just a humidifier and heat mat for the first week, then start exchanging air as roots appear. Running it closed also holds heat and CO² in, which is why a CO² pad works so well here. The 175mm sleeves are there when you want them — they take 150mm ducting, and a small inline on its lowest setting is more than enough. What light should I run in it?Something small and low-heat. A 26W or 42W LED grow bar hung off the shallow bar is the standard choice — cuttings want gentle light, not intensity, and anything bigger will fight you on temperature in a 0.375m² space. Can I use it as a mini grow tent instead of for clones?For seedlings, herbs, microgreens and mother-plant maintenance, yes. At 70cm tall it is not a flowering tent — there is no headroom for a plant to finish. Think of it as the front end of a grow: strike your clones here, then move them into a full-height tent. Is it genuinely lightproof?Yes — the shell is 100% light-proof ADF material and the zips seal closed. The one thing that undoes it is a frame that has not been pushed fully together, which stretches the seams. Assemble it properly and check with the room dark before your first run. What warranty does it come with?Twelve months against manufacturing and materials defects — faulty stitching, delamination, faulty fittings or faulty fabric — backed by Holland Forge, seaHawk's Australian distributor. Zips carry a 3 month defect warranty, so check them on arrival and tell us straight away if anything is wrong. Wear and tear, condensation damage and incorrect setup are not covered. Does it come with a floor tray?It does. A waterproof floor tray zips in and secures with nylon fabric straps, so runoff and spills stay in the tent and off your bench. Strike Rate Starts With Control A sealed, dark, humid room for your cuttings — on a bench, in a cupboard, anywhere. Free shipping over $499*. Add to Cart Browse Propagation Tents