Happymodel Moblite7 Walksnail V3 1S Whoop Drone BNF

The Happymodel Moblite7 Walksnail V3 is a 75mm 1S digital HD brushless whoop built around the SuperX HD ELRS AIO flight controller and Walksnail Avatar video system. It supports 1S LiPo or LiHv batteries and uses a GNB A30 battery plug. Specifications: Frame wheelbase: 75mm Weight: 34.5 gram without battery Size: 98mm*98mm*48mm UART ELRS v3.0 ready: Yes Battery compatibility: 1S Lipo battery or Lihv battery Battery Plug: GNB A30 Onboard blackbox ready: Yes Flight controller: SuperX HD ELRS Betaflight firmware ready: Betaflight 4.4.2 Firmware target: CRAZYBEEF4DX MCU: STM32F411CEU6 (100MHz, 512K FLASH) Sensor: BMI270 or ICM42688P (SPI connection) Power supply input: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V), only support 1s input for this drone ESC: Built-in 12A(each) Blheli_S 4in1 ESC ESC protocol: Dshot300 Receiver: Built-in UART elrs receiver, elrs v3.0 ready, support WIFI and pass-through firmware update Bluejay ESC Firmware ready: Yes BEC: Built-in 5V 1A BEC Voltage detection: Built-in OSD chip: No betaflight analog osd chip Onboard 4in1 ESC power supply: 1-2S LiPo/LiPo HV ESC current: 12A continuous peak 15A (3 seconds) ESC configurator support: Support ESC-Configurator and BLHELI_S Suite configurator ESC factory firmware: Z-H-30 - Bluejay, 0.19, 48kHz ESC default protocol: DSHOT300 Receiver type: Onboard UART ExpressLRS 2.4GHz Receiver RF Frequency: 2.4GHz Receiver antenna: enameled copper wire 31mm length Telemetry output Power: <12dBm Receiver protocol: CRSF Receiver default firmware version: ExpressLRS V3.0.1 Receiver hardware note: The same hardware with Happymodel EP1 receiver Receiver firmware update methods: ExpressLRS configurator or WIFI or Betaflight pass-through Motor model: 1002 20000KV Motor configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: Φ1.5mm Motor Dimension(Dia.*Len): Φ13.5mm*12.5mm Motor weight: 2.5g Motor cells: 1S only Propeller: Gemfan 1610-2 Bi-blades Propeller weight: 0.24g Propeller material: PC Propeller pitch: 1 inch Props Dia: 40mm Center Hole Dia: 1.5mm VTX model: Avatar mini 1s module VTX communication frequency: 5.725-5.850 GHz VTX transmitter power (EIRP): FCC:<25.5dBm; CE:<14dBm; SRRC: <20dBm;MIC:<25dBm VTX I/O interface: JST1.O*6(Power in)JST1.O*4(USB) VTX mounting holes: 25.5*25.5 mm VTX dimensions: 33*33*6.5 mm VTX storage: 8G VTX recording: 1080p/720p VTX weight: 6.8 g VTX operating temperature: -20-40℃ VTX channels: 8 VTX wide power input: 3.1V-5V VTX supported FC system: Betaflight VTX OSD: Canvas mode VTX bitrate: 25mbps / 50mbps VTX latency: Average delay 22ms VTX antenna connector: IPEX Camera model: Avatar nano Camera image sensor: 1/2.7”Inch Camera resolution: 1080P/6Ofps,720P/120fps,72OP/6Ofps Camera ratio: 16/9 4/3 Camera lens: 2.1mm Camera FOV: 170° Camera aperture: F2.0 Camera shutter: Rolling shutter Camera minimum illumination: 0.001Lux Camera weight: 3.5g Camera dimensions: 14*14*17mm Camera coaxial cable: 45mm Package Contents: 1x Mobula7 v4 75mm frame +Canopy 1x SuperX HD ELRS AIO flight controller 4x Happymodel 1002 KV20000 Unibell brushless motor 1x Gemfan 1610-2 bi-blades propeller(4cw+4ccw) 1x Walksnail Avatar nano HD camera 1x Walksnail Avatar mini 1s tx module 1x Spare Canopy 1x Propeller disassemble tool 1x Screw driver