Franklin Electric IGPH-A Series High Head Automatic Grinder Pump - 2 HP 208-230V 1Ph

Description Franklin Electric · Submersible High Head Grinder Pump FPS IGPH-A Series 2 HP dual-stage high-head grinder, 208-230V single-phase, with start and run components sealed in the pump. IGPH for full-range duty, IGPHR for high-head duty above 100 ft; float and no-float builds. 2 HP 3450 RPM Dual-Stage 40 GPM Max Flow 200 ft Max Head 1-1/4 in FNPT Discharge 208-230V 1Ph No Control Panel Needed 10.9 W x 18.8 H in 109 lb Weight Overview The FPS IGPH Series is Franklin Electric's dual-stage, high-head grinder pump for the toughest residential and commercial wastewater service: sewage lift stations, and low-pressure sewer systems for housing developments and lake communities where high vertical lift or long force mains are present. Two brass impellers in series (dual-stage hydraulics) build the head. Ahead of them a cutting mechanism grinds solids at 414,000 cuts per minute. The 2 HP, 3450 RPM motor has built-in overload protection, a carbon/ceramic mechanical seal and a short, deflection-resistant shaft, in epoxy-coated cast iron. The start and run components are encased in an oil-free chamber, so the pump starts without a control panel. The float builds (515713, 515701) run automatically; the no-float builds (515716, 515711) are for basins where level is switched externally. IGPH or IGPHR? Both are 2 HP dual-stage pumps. The IGPH is rated across its whole curve, from 40 GPM at 10 ft to 10 GPM at 175 ft. The IGPHR is rated only in the high-head region above the line Franklin marks at about 100 ft, and draws 16 FLA against the IGPH 18.5 FLA single-phase. Choose the IGPHR only where the total head stays above 100 ft. Genuine Franklin Electric equipment, factory-new in original packaging — sold and supported by Watermain Supply, an independent industrial supplier. Warranty: 12 months from the date of purchase. Growth & Multiplex Runs as a simplex station, or as a duplex with two pumps alternating from a duplex grinder panel. The IGPH-M231 is the high-head option in the PowerSewer V4PS station. Models & Ratings Model Part No. Float Switch FLA / Watts Weight lb IGPH-A231-30 515713 Float 18.5 / 3600 109 IGPH-A231-30 515716 No float 18.5 / 3600 109 IGPHR-A231-30 515701 Float 16 / 3600 109 IGPHR-A231-30 515711 No float 16 / 3600 109 All 2 HP, 60 Hz, 30 ft cord. Source: FPS Wastewater Catalog M5276 (09-25) and Franklin Electric price list 996791 (June 2026). Specifications Specification Value Motor 2 HP, 3450 RPM; single-phase capacitor start, capacitor run Hydraulics Dual-stage, upper and lower brass impellers Insulation class F Overload protection Internal, on-winding thermal protector Discharge 1.25 in vertical FNPT Cutting 414,000 cuts per minute Start components Encased in an oil-free chamber in the pump Dimensions 10.9 in wide; 18.8 in high Power cable Type SOW or SOOW 12/3, 30 ft Patent U.S. Patent No. 7,237,736 Source: FPS Wastewater Catalog M5276 (09-25), IGPH-A spec sheet 996738. Performance — Will It Do What You Need? Find your total dynamic head across the top: the vertical lift from the basin to the highest point of the force main plus friction in the pipe. The figure below it is gallons per minute at that head. Head (TDH) 10 ft 25 ft 50 ft 75 ft 100 ft 125 ft 150 ft 175 ft Shut-Off IGPH, GPM 40 39 36 33 30 24 18 10 200 ft IGPHR, GPM - - - - 30 24 18 10 200 ft Manufacturer tabulated points only. IGPHR models are rated only above the line Franklin marks on the curve at about 100 ft, so no IGPHR points are published below 100 ft; a dash means no rated point. Shut-off is the head at zero flow. Source: FPS Wastewater Catalog M5276 (09-25), IGPH-M spec sheet 996739 and IGPH-A spec sheet 996738. The dual-stage IGPH keeps 30 GPM at 100 ft, where the single-stage IGP is down to 20 GPM, which is why Franklin specifies it for long force mains and high vertical lift. Before You Buy — The Limits That Decide the Fit Limit Value Liquid Residential sewage, effluent, wastewater and other non-explosive, non-abrasive, non-corrosive liquids Basin Gas-tight basin at least 24 in diameter and 48 in deep, vented to local, state and federal plumbing code Discharge piping No smaller than the 1-1/4 in pump discharge; ABS, PVC, polyethylene or stainless steel. Full-flow ball check valve mounted horizontally, a 3/16 in air-relief hole between pump and check valve, and a shut-off valve after the check valve Power 208-230V single-phase on its own branch circuit with a double-pole disconnect near the pump Level control Float builds run automatically; no-float builds need external level control, wired to a panel without start components (515352 or 515363) IGPHR head range Rated only above about 100 ft total head App None Materials of Construction Component Material Motor cover Cast iron with epoxy coating Motor cover O-ring Nitrile Motor shaft AISI 300 series stainless steel (in contact with fluid pumped) Upper bearing Single row ball, 6203 Lower bearing Single row ball, 6306 Seal housing Cast iron with epoxy coating Mechanical seal Carbon/ceramic Volute Cast iron with epoxy coating Impellers Brass, upper and lower Rotating cutter AISI 440C stainless steel, through-hardened to Rockwell 55-60C Stationary cutter AISI 440C stainless steel, hardened to Rockwell 55-60C External hardware 300 series stainless steel Power cable Type SOW or SOOW 12/3 Source: FPS Wastewater Catalog M5276 (09-25), construction tables. Accessories Accessory Order No. Where to buy 1.25 in Base Elbow / Base Elbow with Check Valve 115930101 / 115930102 Grinder accessories and parts 1.25 in Check Valve, ductile iron ball 115930120 Grinder accessories and parts 1.25 in Vertical Flange Discharge Adapter 115383 Grinder accessories and parts Horizontal Discharge Adapter Kit 515837 Grinder accessories and parts Service Parts Part Order No. Where to buy Capacitor Replacement Kit, IGP and IGPH, 208-230V 520859 Grinder accessories and parts Seal Ring, 7.356 ID x 0.134 wall 928048 Grinder accessories and parts Grinder Leg Kit (GLK) 599078 Grinder accessories and parts Confirm fit against the pump nameplate before ordering; Franklin publishes no separate IGPH parts list in the catalog. For engineering-led sizing and selection support or a factory submittal, email sales@watermainsupply.com or call 1-888.510.4036. © Watermain Supply — A division of E4 Industrial LLC Data Sheet FPS Wastewater Product Catalog (M5276) Videos FPS High Head Grinder