MAXKOSKO In-Pipe Heating Cable with Y-Fitting for Drinking Water Pipes, 120V CSA Self-Regulating Heat Trace with GFCI

In-Pipe Drinking Water Heating Cable with Integrated Y-Fitting MAXKOSKO In-Pipe Heating Cable with Brass Y-Fitting provides internal freeze protection for compatible pressurized drinking water lines, buried pipes, well systems, cabins, farms, and seasonal properties. The integrated brass Y-fitting creates a smoother 45° cable entry path, reducing the need to source a separate T-fitting and simplifying installation compared with the standard in-pipe model. Integrated Brass Y-Fitting Provides a built-in cable entry point with a smoother 45° insertion angle. Potable Water Certified CSA and NSF/ANSI 61 certification support use in compatible drinking water pipe systems. 230 PSI Pressure Rating Designed for compatible pressurized residential, rural, well, and farm water lines. Built-In GFCI Plug Adds electrical leakage protection for properly installed 120V wet-location applications. Important Before Ordering Inspect the Cable and Confirm the Pipe Route Integrated Fitting: The brass Y-fitting is included, reducing the need to purchase a separate T-fitting for the main cable entry. Recommended Pipe Size: Designed for compatible pipes 3/4 in and larger. Confirm that every pipe connection, adapter, valve, and bend provides enough internal clearance. No Sharp Elbows: Do not force the cable through sharp elbows, restricted fittings, blockages, collapsed pipes, or unknown internal routes. Factory Inspected: Every MAXKOSKO cable is fully inspected before shipment. Inspect the complete outer jacket, end seal, and fitting again before installation. Outer Jacket Must Be Undamaged: Cuts, cracks, abrasion, crushing, or end-seal damage can cause leakage or electrical failure. Do not install a damaged cable. Contact Support: If you find any damage before installation, stop and email photos to maxkosko@maxkosko.com. Avoid Forceful Installation: Insert the cable slowly and gently. Pulling, hammering, twisting, or forcing it through a tight route can damage the outer jacket and lead to water leakage. Specifications Product Type In-Pipe Drinking Water Heating Cable with Integrated Y-Fitting Rated Voltage 120V AC Heat Output Approximately 3W/ft at 50°F (10°C) Maximum Water Pressure 230 PSI Pipe Entry Integrated Heavy-Duty Brass Y-Fitting Entry Angle Approximately 45° Recommended Pipe Size 3/4 in and Larger Application Pressurized Potable Water Pipe Freeze Protection Certification CSA and NSF/ANSI 61 Electrical Protection Built-In GFCI Plug Outer Jacket Potable-Water-Compatible Fluoropolymer Field Modification Do Not Cut, Shorten or Splice the Heating Cable Compare MAXKOSKO In-Pipe Heating Cables View Comparison Hide Comparison Product Best For Pipe Entry Main Difference Standard Potable Water Cable Pressurized drinking water, wells, cabins, buried water lines Separate T-fitting required 230 PSI, 3W/ft, 120V or 240V options Y-Fitting Potable Water Cable Pressurized drinking water where easier insertion is preferred Integrated brass Y-fitting 230 PSI, NSF/ANSI 61, easier 45° cable entry Upgraded 5W Water & Sewer Cable Sewer, septic, sump, and drain systems Confirm compatible entry fitting 5W/ft, broader application range, built-in GFCI plug Standard Sewage Pipe Cable Sewer, septic, wastewater, sump, and drainage applications Confirm compatible drain entry Non-potable applications, 100 PSI, lower-output option Basic Installation Requirements View Requirements Hide Requirements Confirm the pipe size, cable length, pressure, and internal route before ordering. Shut off and drain the water supply before installing the Y-fitting. Inspect the cable jacket and end seal before insertion. Insert the cable gradually through the 45° Y-fitting entry. Do not force the cable through sharp bends or narrow pipe components. Complete all seals and pressure-test the plumbing before restoring service. Read the complete product manual before installation. Frequently Asked Questions What is the advantage of the Y-fitting version? The included brass Y-fitting provides an integrated cable entry with a smoother 45° angle, reducing cable stress and simplifying installation. Is it suitable for drinking water? Yes. This model is designed for compatible potable water systems and is listed as CSA and NSF/ANSI 61 certified. Can I force it through a tight elbow? No. Forceful installation can damage the outer jacket or end seal and may cause leakage. The pipe route must allow smooth and gradual cable insertion. What if I notice a cut or abrasion before installation? Do not install the cable. Send photos and your order details to maxkosko@maxkosko.com. Does it include automatic thermostat control? No. Self-regulating technology adjusts heat output but does not fully turn off. Pair it with the MAXKOSKO 120V Thermostat Controller for automatic temperature-based power control. Controller & Product Selection For automatic seasonal control and reduced energy use, pair this cable with the MAXKOSKO 120V Pipe Heating Cable Thermostat Controller. Before ordering, confirm that the line is a pressurized drinking water pipe and that the cable route does not include sharp or restricted internal bends.