Essential Central Bar Pillar Cake Separator
Essential Central Bar Pillar Cake Separator Lift between your tiers, sized and coloured your way. Key Features Exclusively designed and 3D printed by Prop Options in the UK Modular build: pick the plate pairing and the central pillar height that suit your cake Ten plate pairings, from a compact 4" top with 4" base up to a 10" top with 10" base Five pillar heights: 2", 3", 4", 6" and 8" Five colours drawn from The Muse Cake Stand palette, so your props match across a design Food-safe Eco PLA, strong enough for real cake when the tiers are dowelled correctly Our most cost effective route into a central bar separator What is the Essential Central Bar Separator? It is the simplest way to open up a gap between two tiers. A single central pillar sits between a top plate and a base plate, holding the tier above clear of the one below so you get that raised, floating look without a full stand. Because the top plate, the base plate and the pillar are all chosen separately, you can match the separator to the cake rather than the other way round. A 4" top plate over a 10" base gives a stepped, tapered profile. Matching plates give a clean column. Every set is 3D printed to order in food-safe Eco PLA and finished in the colour you choose, so it either disappears into the design or becomes part of it. Choosing Your Combination Top plate should suit the tier sitting on it. Match it to the tier diameter, or go slightly smaller for a floating edge. Base plate should suit the tier underneath. Larger bases spread the load and give a more stable, stepped look. Pillar height sets the gap. 2" and 3" give a subtle lift, 4" and 6" are the popular middle ground for display, and 8" creates a dramatic open space for florals or props. Built to Perform Plate diameters of 4", 6", 8" and 10", paired in ten combinations Pillar heights of 2", 3", 4", 6" and 8" Central pillar locates into both plates for a square, level stack Printed at high resolution in durable Eco PLA that holds its shape under load Suitable for real cake and dummy tiers alike Wipe-clean surface that photographs cleanly under studio and venue lighting Prop Options vs Common Replicas Feature Prop Options Common Replicas Original product design ✅ ❌ Patent pending protection ✅ ❌ Food-safe, professional-grade Eco PLA ✅ Often low-cost & inconsistent Mix and match plate and pillar sizing ✅ ❌ Trusted by leading cake makers, worldwide ✅ ❌ Dedicated customer support & reliability ✅ Varies or unavailable Why Prop Options? Global no.1 for cake stands, props and professional cake tools Registered product designs, trusted worldwide Durable, professional-grade build Made for cake professionals UK-based with fast global delivery FAQs Which plate sizes should I pick? Start with the tier that sits on top and choose a top plate to match or sit just inside it. Then choose a base plate that suits the tier below. Matching plates give a straight column look, while a smaller top over a larger base gives a stepped, tapered profile. Is it strong enough to hold real cake? Yes. Dowel the tier below as you normally would, set the separator level and centred, and the plates will carry a real cake safely. For tall or heavy builds, use a larger base plate and keep the pillar height sensible. What colour are the top and base plates? To keep the range as budget-friendly as possible, the top and base plates are white as standard and designed to be easily covered to complement your cake design. Why is this cheaper than your other separators? The Essential range strips the design back to what does the work: two plates and one central pillar, printed in the same food-safe material as the rest of the range. You get the height and the finish without paying for the extra columns and fixings of our larger separator systems. Can I buy extra pillars or plates on their own? Yes. Individual central pillars are listed separately, so you can build up a set of heights over time and swap them into the same plates. Do the colours match your other products? They do. The five colours here are taken from the same palette used on The Muse Cake Stand, so a separator can be matched to a stand across the same design. How do I clean it? Wipe clean with warm soapy water only. Avoid abrasive cloths and harsh detergents, and do not put it in the dishwasher. Please wash before first use. Product Details Designed & made by: Prop Options Material: Food-safe Eco PLA filament, 3D printed Plate diameters: 4", 6", 8" and 10", in ten pairings Pillar heights: 2", 3", 4", 6" and 8" Shape: Round Colours: White, Black, Gold, Navy and Pastel Pink (all plates are white) Supplied as: One top plate, one base plate and one central pillar Care: Wipe clean with warm soapy water only, not dishwasher safe Stock status: Printed to order Complete the Set Need more height, more columns or a different profile? Browse the full Cake Separators & Spacers collection, or match your separator to a stand from The Muse Cake Stand in a matching colour. Important Information Always set your separator level and centred, and dowel tiered cakes as you normally would. Taller pillars raise the centre of gravity, so pair them with a larger base plate and take extra care when transporting. Please follow all standard cake construction guidelines when building tiered displays. Cake Design by Savanna The perfect way to sketch your cake designs. Explore our official Procreate Stamp and Brush sets to enhance your business and design beautiful cakes for your customers. View The Collection
4" top with 4" base, 4" top with 6" base, 4" top with 8" base, 4" top with 10" base, 6" top with 6" base, 6" top with 8" base, 6" top with 10" base, 8" top with 8" base, 8" top with 10" base, 10" top with 10" base
2" Central Pillar, 3" Central Pillar, 4" Central Pillar, 6" Central Pillar, 8" Central Pillar