Sky Lumen 17mm DriverVNE

This is a FET Driver so 100% = Direct driven Driver must be thermal epoxy to host for cooling Connections might have to be thermal potted for ultra high drain applications DriverVNE Main User Interface · From OFF: Quick Click = ON, Press & Hold = Low or first mode in sequence · From ON: Quick Click = OFF, Press & Hold = Cycle sequence such as Low-Medium-High Hidden Features (From ON or OFF) 2x Rapid Clicks = 100% Turbo · 3x Rapid Clicks = Strobe · 4x Rapid Clicks = Voltage o Voltage Blinks § 5 blinks > 90% § 4 blinks > 70% § 3 blinks > 50% § 2 blinks > 30% § 1 blink < 30% · 5x Rapid Clicks = Bike Strobe · 6x Rapid Clicks = 1 Hz Blink · 7x Rapid Clicks = 2 Hz Blink · 8x Rapid Clicks = Random Hz Techno Strobe Note: Hidden Features can be activated from ON or OFF. Note: While in Hidden Features, Quick Click revert back to last mode used. Note: Hidden Features are disabled when Config. Lock is enabled. Config Mode · 10 Quick Clicks from ON or OFF enters Config Mode. Light will blink 5 times if activated or blinks 15 times if Config Mode is locked out. · Each setting has 3 groups of Clicks. · Example: 10-1-12 = 10 Clicks, then 1 Click, then 12 Clicks (Blinking confirmation between each set of Clicks.) * = Default Setting Mode Group Selection · The light will turn on in a low level while you are making your selection. · After selecting the mode group, the light will blink 2 times to confirm the selection. 10-1-1 = 100% 10-1-2 = 70% 10-1-3 = 50% 10-1-4 = 30% 10-1-5 = 15% 10-1-6 = 5% 10-1-7 = FF – 50% 10-1-8 = 5% – 50% 10-1-9 = 20% – 50% 10-1-10 = FF – 20% – 50% 10-1-11= FF – 5% – 15% – 40% – 70%* 10-1-12 = 100%-70%-40%-15%-5%-FF 10-1-13 = FF – 20% – 50%. Lender’s Group with Hidden Features Deactivated. 10-1-14 = Bike 20%, Bike 40%, Bike 70%, 100% Constant ON FireFly Level Config 10-2-1 = Dim FireFly 10-2-2 = Low FireFly 10-2-3 = Medium FireFly 10-2-4 = High FireFly 10-2-5 = Bright FireFly Turbo Level Config 10-3-1 = 100%* 10-3-2 = 90% 10-3-3 = 85% 10-3-4 = 80% 10-3-5 = 75% Turbo Timer Config (Constant Turbo Mode Only) · Once turbo time is reached, the light begins a slow linear ramp down to 50% that takes ~1 min. to complete. 10-4-1 = TT OFF 10-4-2 = 15s 10-4-3 = 30s * 10-4-4 = 45s 10-4-5 = 1min 10-4-6 = 1.5min 10-4-7 = 2min 10-4-8 = 2.5min 10-4-9 = 3min 10-4-10 = 5min 10-4-11= 7min 10-4-12 = 10min Temperature Sensor Config 10-5-1 · The light activates at 15% power. · A click in the first 5 seconds turn the temperature sensor OFF. · After 5 seconds, the light will turn on at “Turbo” power. o Click once again once the desired peak temperature is reached. Battery Insert LED Start-UP 10-6-1 = OFF * 10-6-2 = ON 100% 10-6-3 = ON 50% 10-6-4 = ON 5% Low Voltage Protection Toggle (Begins at 2.8V/cell under load; shutdown at 2.5V/cell under load). 10-7-1 = LVP Disabled 10-7-2 = LVP Enabled * 10-7-3 = LVP Enabled (Lower Threshold --- For Super High Power Lights) Light Lock Out Toggle | Done from OFF state. Resets with power reset. 10 Click with 10th Click & Hold · 1 Blink = Unlocked* · 2 Blinks = Locked Turbo Mode Toggle | Done from OFF state. Persists with power reset. 13 Click with 13th Click & Hold · Constant Turbo = Turbo at 100% until Temp Sensor or Turbo Timer intervene. · Adaptive Vision Turbo = Turbo / Power Level over 30% for 15s, then a constant ramp down until 30% over a ~10min duration. o Saves battery, lowers heat, protects circuitry, and allows eyes to adapt. · 1 Blink = Constant Turbo* · 2 Blinks = Adaptive Turbo Config Lock Toggle | Done from OFF state. Persists with power reset. 15 Clicks with 15th Click & Hold · 1 Blink = Unlocked* · 2 Blinks = Locked + Extended Warranty + International Shipping Insurance Must Read Purchase Agreement SkyLumen54@gmail.com