Stock Driveshaft | RAM 2500/3500 4WD Truck (2014-2018) | Steel | 1555 Series | 3.5" OD
Stock Replacement Two Piece Steel Driveshaft - Steel, 3.5 Inch OD, 1550/1555 Series Dodge Ram 2500 4x4 Truck - 2014 to 2018 This is a complete stock replacement driveshaft balanced and ready for install. This driveshaft is built to be a direct replacement. If you are looking for an upgrade option see our one piece conversion driveshaft. FREE GROUND SHIPPING INSIDE THE USA (This product does not qualify for international shipping) Notes Specs Vehicle Fitment Heavy Duty 3.5 Inch Steel Driveshaft This driveshaft is a direct replacement for the 2003 to 2018 Dodge Ram 2500 four wheel drive and two wheel drive crew cab long bed trucks. This direct replacement driveshaft has replaceable components including the premium u-joint and center bearing. We will need you to measure for the driveshaft to verify proper fit. Measuring is very easy to do - just follow the diagram below. This driveshaft is heavy duty from end to end. We use only the highest quality 1550/1555 universal joints from top brands such as Spicer or Neapco. The driveshaft comes fully assembled, balanced, and ready to bolt in. Installation is as simple as sliding in the transfer case yoke and bolting up the flange. It is not common but it is always a good idea to check for clearance issues with the carrier bearing cross member to ensure that the cross member does not need to be removed. This is a 100% new driveshaft including a new transfer case slip yoke, center bearing, new driveshaft and new flange. This is an all new direct replacement driveshaft. All you have to do is remove your old shaft and bolt up the new driveshaft. You won't be disappointed with heavy duty replacement driveshaft, built here in South Bend, Indiana. Time and again customers are impressed at how well made the driveshaft is and - no matter the application a daily driver or and over the road towing rig or pulling truck. Free Ground Shipping Seamless Steel Tubing Precision Balancing Premium Sealed OEM U-Joints Custom Length Options Lifetime Weld Warranty . Weld Yoke Material: Forged Steel Tube Material: 0.095 Inch Wall DOM Seamless Steel Tube Outside Diameter: 3.5 Inch OD (Measuring Guide - Tube OD) U-Joint: Neapco 3-0155G Universal Joint Spicer SPL70X Universal Joint U-Joint Information: 1550 Series / Premium Non-Greasable 1-3⁄8(1.375)" Cap x 4-31⁄32(4.969)" Span (Measuring Guide - U-Joint) Max Custom Length: Measure from seal to center bearing and then from center bearing to flat for flange on the differential. Transmission Slip Yoke: Included Flange Yoke: Included Vehicle Fitment Model: Dodge Make: Ram 2500 and Ram 3500 Years: 2014-2018 Drive Type: 2WD & 4WD Cab Sizes: Regular Cab, Quad Cab, Crew Cab, and Mega Cab Bed Size: Short Bed and Long Bed U-Joint Series: 1555 - This 1550/1555 driveshaft is an upgrade form the stock 1410 & 1480 OEM series universal joint. Engine: Gas and Diesel Transmission: Automatic and Manual If you have any questions we are here to help: CHAT | PHONE (574)287-9650 | CONTACT US FREE GROUND SHIPPING INSIDE THE USA (This product does not qualify for international shipping) Required Driveshaft Measurements: There are several driveshaft lengths and combinations for these vehicles before we build your driveshaft we will need you to confirm your dimensions. You can place your order today and we will send a follow up email requesting your driveshaft length or your can submit your measurement below. We will need to know your driveshaft length and the length of exposed spline. (A): Measurement will be taken from the transfer case or transmission seal to the middle of the center bearing. (B): Measurement will be taken from the center bearing to the flat face of the differential where the driveshaft 4 bolt flange mounts. (C): Exposed spline from the seal. [EXAMPLE: A) 40in, B) 45in, C) 1in] We cannot complete your driveshaft order until we have your driveshaft lengths.
Driveshaft Only, Driveshaft with Bolt Kit