Flashark Cold Air Intake Kit for 2018-2024 Jeep Wrangler JL & Gladiator JT 3.6L

The 3.6L Pentastar V6 in your 2018-2024 Jeep Wrangler JL or Gladiator JT is a proven powerplant — but the factory airbox suffocates it with a narrow, sound-tuned intake tract designed for cabin quietness, not performance. The Flashark Cold Air Intake Kit replaces that restrictive stock assembly with a smooth 3-inch (76mm) mandrel-bent aluminum tube, a high-flow dry cotton gauze filter, and a sealed heat shield that draws cooler, denser air from outside the engine bay. The result is an estimated 7-10% horsepower gain (20-29 HP) and 5-7% more torque (13-18 lb-ft), with noticeably sharper throttle response and a deeper intake growl under acceleration. The black powder-coated finish resists under-hood heat and corrosion, while the dry filter eliminates the messy oiling process and MAF sensor contamination risk common with oiled filters on the Pentastar platform. Bolt-on installation takes about 30-45 minutes with basic hand tools — no cutting, no drilling, no tune, no check engine lights. ⚠️ Note: This intake is designed for the 3.6L Pentastar V6 only. It does NOT fit the 2.0L turbo I4, 3.0L EcoDiesel V6, or 6.4L V8 (Rubicon 392) models. It also does NOT fit the 2012-2018 Wrangler JK — that is a different platform requiring a different intake kit (BQM0004005). Key Features 3" (76mm) Mandrel-Bent Aluminum Tube — Smooth, unrestricted airflow path replaces the factory corrugated intake tube; black powder-coated finish for heat resistance and corrosion protection Dry Cotton Gauze Filter — No Oil Required — High-flow washable dry filter element; no oiling means zero risk of MAF sensor contamination, a known issue with oiled filters on the 3.6L Pentastar V6 Sealed Heat Shield with Edge Trim — Isolates the filter from engine-bay heat, pulling cooler, denser air for consistent power delivery; black edge trim ensures a tight seal against the hood liner Estimated 7-10% Horsepower Gain (20-29 HP) — Based on stock 285 HP 3.6L Pentastar; eTorque-equipped models see similar gains; actual results vary with altitude, fuel quality, and vehicle condition Estimated 5-7% Torque Gain (13-18 lb-ft) — Improved low-to-mid range torque for better crawling response off-road and smoother highway merging Deeper Intake Growl — Replaces the muffled factory intake note with a more aggressive induction sound under load — noticeable under acceleration but quiet at idle and cruise Washable & Reusable Filter — Clean every 15,000-20,000 miles (5,000-10,000 in dusty off-road conditions); saves money over disposable paper filters and reduces waste Complete Bolt-On Kit — Includes all couplers, clamps, hardware, and installation guide; typical install time 30-45 minutes with basic hand tools; reversible to stock at any time Specifications SKU: BQM0004006 Brand: Flashark Vehicle Fitment: 2018-2024 Jeep Wrangler JL (2-door & 4-door Unlimited) & 2020-2024 Jeep Gladiator JT Engine: 3.6L V6 Pentastar (345 cu.in.) Pipe Diameter: 76mm (3.0") Pipe Material: Aluminum piping Tubing Finish: Black powder-coated Filter Type: Dry cotton gauze (no oil required) Filter Color: Red Heat Shield: Black powder-coated steel with edge trim Couplers: Silicone reducer couplers Clamps: Stainless steel T-bolt clamps Horsepower Gain: 7-10% (approx. 20-29 HP on stock 285 HP 3.6L Pentastar) Torque Gain: 5-7% (approx. 13-18 lb-ft on stock 260 lb-ft) Tuning Required: No CEL Risk: None (designed to work with stock MAF sensor readings) Installation Time: 30-45 minutes Tools Required: Basic hand tools (socket set, screwdriver, pliers) Filter Maintenance: Clean every 15,000-20,000 miles (5,000-10,000 in dusty conditions) Warranty: 1 Year Emissions Note: Does not modify emissions systems; street-legal in most states Customer Service: service@flasharkracing.com Shop More Cold Air Intake Kits Jeep Cold Air Intake Kits Package Includes 1x Black powder-coated aluminum intake tube (76mm / 3.0") 1x Red dry cotton gauze cone filter 1x Black powder-coated steel heat shield 1x Black edge trim (for heat shield sealing) 2x Silicone reducer couplers 4x Stainless steel T-bolt clamps 1x Installation hardware kit (bolts, washers, nuts, brackets) 1x Installation instructions manual