Mytee HP90 Stingray™ Heated Automotive Detail Extractor | 5 Gallon, 1,200W REAL HEAT™

Full-size extraction heat in a body you can still move The Mytee HP90 Stingray is what a detailer buys when the compact machine is no longer keeping up. It runs 1,200 watts of REAL HEAT™ and reaches 210 degrees Fahrenheit at the tool. It carries 5 gallons of solution and 5 gallons of recovery. It weighs 65 pounds and rolls on 3-inch locking casters all the way around, which means one person still moves it without a second set of hands. That combination is the whole point of the machine. Shop-level heat and capacity, in a footprint that fits a van and a two-bay shop. What 210 degrees actually does Temperature is the variable most detailers underuse. Hot water breaks the bond between soil and fiber instead of just diluting it. At 210 degrees, body oils in seat foam liquefy rather than smear. Ground-in road film and winter salt release on the first pass. Coffee, soda, and protein stains that survive a cold extraction come up without repeated wetting. The practical result is fewer passes, which means less water in the seat, which means shorter dry time. Dry time is the part your customer actually experiences. Mytee's REAL HEAT™ system holds temperature under continuous use rather than dropping off after the first few minutes. That distinction matters on a full interior, where a heater that fades halfway through is the same as no heater at all. Where the HP90 sits against the 8070 This is worth being straight about, because most sellers will not tell you. The HP90 and the compact Mytee 8070 share the same vacuum motor and the same pump. Both produce 130 inches of water lift at 100 CFM. Both deliver 120 PSI at 1.3 gallons per minute. The HP90 is not a suction upgrade. It is a heat and capacity upgrade. You get 1,200 watts and 210 degrees instead of 1,000 watts. You get 5-gallon tanks instead of 4-gallon. You give up about 20 pounds of portability. Buy the HP90 if you are refilling the compact machine mid-job, or if the interiors you clean are heavily soiled enough that heat is the limiting factor. Buy the 8070 if daily lifting into a van matters more than tank size, or if your work runs lighter. Neither answer is wrong. They are different jobs. Power requirements, stated plainly The HP90 draws 20 amps at 110 to 120 volts on a single 25-foot 12/3 cord. That is a full 20-amp circuit. A standard 15-amp household outlet will not carry it, and sharing a 20-amp circuit with anything else will trip the breaker. Plan for a dedicated 20-amp outlet in the bay, or verify the circuit before a mobile job in a residential driveway. This catches people, and it is better to know now than in someone's garage. The single-cord design is still an advantage. Machines in this class that require two circuits are considerably harder to place. Built to work, built to last The housing is roto-molded polyethylene. It does not rust, it does not dent, and it tolerates being loaded and unloaded for years. Molded carry handles let two people lift it into a vehicle cleanly. Three-inch locking casters on all four corners mean it rolls easily and then stays put once you are working. A stainless steel shut-off switch in the recovery tank prevents overfill, which is the failure that ruins vacuum motors on cheaper machines. The 15-foot vacuum and solution hose combo reaches across a full-size SUV from one parking position. The 4-inch Air Lite™ upholstery tool is sized for seats, door panels, floor mats, and cargo areas. A neoprene Heatguard™ hose wrap keeps the hot solution line off door sills and paint. Who this machine is right for The HP90 fits busy detail shops, dealership recon departments, mobile operators running heavy interiors, and rental car or fleet operations cleaning their own vehicles. It is the right call if you clean four or more interiors a day, if heavily soiled work is normal rather than occasional, or if you are tired of refilling a 4-gallon machine. It is more machine than a light-duty operation needs. If you clean one or two clean interiors a day and lift the machine alone every morning, the Mytee 8070 is the better buy and costs less. Stainless steel tool option The HP90-SS is the same machine with a stainless steel upholstery tool in place of the standard Air Lite™ tool. Detailers running continuous high-heat work often prefer the stainless version. For most operations the standard HP90 is the right choice. Factory support, direct from Mytee Mytee builds this machine in San Diego and backs it with factory technical support. For questions about operation, parts, or service on your HP90, Mytee's support team is the fastest and most authoritative resource, and they are the people to call first. Mytee publishes the full documentation library for the HP90, including the operator manual, quick-start guide, parts lists, and wiring schematics. Buy from an authorized dealer This part costs people real money, so it is worth stating plainly. Mytee's warranty policy says that products sold by unauthorized sellers are not covered by manufacturer warranty or support. A gray-market HP90 from a marketplace listing may look like a bargain until the heater fails in month eight and Mytee has no obligation to help. Rightlook is an authorized Mytee dealer. Buy here and the warranty is intact from day one. Why buy the Mytee HP90 from Rightlook Rightlook has been in the auto enhancement industry since 1998. We train operators, we build detail shops, and we have specified equipment for thousands of auto enhancement startups. That background shapes what we sell and how we sell it. We know which machine fits a two-bay shop versus a mobile rig versus a dealership recon line, because we have set all three up. If you are weighing the HP90 against the 8070 or the HP120 Grand Prix, reach out before you order and we will walk you through the differences. Specifications Specification Mytee HP90 Stingray Model number HP90 (HP90-SS with stainless steel tool) Manufacturer Mytee LLC, San Diego, CA Solution tank 5 gallons (19 L) Recovery tank 5 gallons (19 L) Heater 1,200 watt REAL HEAT™ Maximum temperature 210°F Vacuum motor Single 3-stage Water lift 130 inches Airflow 100 CFM Pump Diaphragm demand Pump pressure 120 PSI Flow rate 1.3 GPM Power cord Single 25 ft, 12/3 gauge Amp draw 20 amps at 110–120V, 60 Hz Hose 15 ft vacuum + solution combo, 1.25 in Included tool 4 in Air Lite™ upholstery tool Dimensions 28 x 16 x 32 in Net weight 65 lbs Shipping weight 80 lbs Shipping dimensions 29 x 15.5 x 33 in Housing Roto-molded polyethylene Casters 3 in locking casters, all four corners Recovery tank safety Stainless steel shut-off switch In the box HP90 Stingray machine, 15 ft vacuum and solution hose combo, 4 in Air Lite™ upholstery tool, neoprene Heatguard™ hose wrap, faucet fill adapter, operator manual. Warranty at a glance The HP90 carries Mytee's limited warranty. One year on parts and domestic labor across all components. Two years on the major components, meaning the pump, the vacuum motor, and the heater. Ten years on the rotationally molded housing and tanks. Coverage runs to the original purchaser and requires that the machine was purchased from Mytee or an authorized Mytee dealer. Read the full Mytee Limited Warranty Policy before you buy anywhere. Coverage Term Parts and domestic labor, all components 1 year from date of original purchase Major components: pump, vacuum motor, heater 2 years from date of original purchase Rotationally molded housing and tanks 10 years from date of original purchase Spare parts purchased direct from Mytee 90 days from date of purchase What the warranty does not cover Warranty is valid for the original purchaser only and begins on the date of customer purchase. Coverage requires purchase from Mytee or an authorized Mytee dealer or service center. Products sold by unauthorized sellers are not covered by manufacturer warranty or support. Coverage is void with misapplication, abuse, lack of maintenance, negligence, abnormal use, alteration of design, use of incompatible or corrosive chemicals, use in a rental service, or service and repairs performed by anyone other than Mytee or an authorized dealer. Normal wear parts are not covered. Major component and housing coverage does not include shipping or labor. These products are intended for commercial, industrial, or institutional use by adults trained in their operation. Read the full Mytee Limited Warranty Policy for complete terms. Frequently Asked Questions How hot does the Mytee HP90 get? The Mytee HP90 Stingray reaches a maximum temperature of 210 degrees Fahrenheit using its 1,200-watt REAL HEAT™ system. How many gallons is the Mytee HP90? The Mytee HP90 has a 5-gallon solution tank and a 5-gallon recovery tank. What is the difference between the Mytee HP90 and the Mytee 8070? Both machines use the same vacuum motor and the same pump, producing 130 inches of water lift at 100 CFM and 120 PSI at 1.3 GPM. The HP90 upgrades heat and capacity, with a 1,200-watt heater reaching 210 degrees and 5-gallon tanks, compared to the 8070's 1,000-watt heater and 4-gallon tanks. The HP90 weighs 65 pounds and the 8070 weighs 45 pounds. What circuit does the Mytee HP90 need? The Mytee HP90 draws 20 amps at 110 to 120 volts and requires a dedicated 20-amp circuit. A standard 15-amp household outlet will not support it. How much does the Mytee HP90 weigh? The Mytee HP90 weighs 65 pounds empty. Shipping weight is 80 pounds. Does the Mytee HP90 need two power cords? No. The Mytee HP90 runs on a single 25-foot 12/3 power cord, including the heater. Is the Mytee HP90 good for auto detailing? Yes. The HP90 Stingray was built specifically for automotive interiors. Its 5-gallon capacity, 210-degree heat, 15-foot hose, and 4-inch upholstery tool are sized for seats, carpets, floor mats, and cargo areas in cars, trucks, SUVs, and vans. What is the difference between the Mytee HP90 and the HP90-SS? The machines are identical except for the upholstery tool. The HP90 ships with the standard 4-inch Air Lite™ tool. The HP90-SS ships with a stainless steel version of the same tool. What is the warranty on the Mytee HP90? The Mytee HP90 carries a one-year limited warranty on parts and domestic labor for all components, a two-year warranty on major components including the pump, vacuum motor, and heater, and a ten-year warranty on the rotationally molded housing and tanks. Coverage begins on the date of purchase and applies to the original purchaser only. Does the Mytee warranty apply if I buy from a third-party seller? No. Mytee's limited warranty policy states that products sold by unauthorized sellers are not covered by manufacturer warranty or support. Coverage requires purchase from Mytee or an authorized Mytee dealer or service center. Rightlook is an authorized Mytee dealer. Who provides technical support for the Mytee HP90? Mytee provides factory technical support for the HP90 direct from their San Diego facility, along with the full documentation library including the operator manual, parts lists, and wiring schematics.