GE Washer Inner Tub Assembly Kit WG04F11975 — Restore Full Drum & Tub Function

OEM Replacement Kit GE Washer Inner Tub Assembly Kit WG04F11975 — Restore Full Drum & Tub Function Basket WG04F11975 Rear Tub WG04F11961 Front Tub WG04L06847 Gasket WG04L06826 Fits GE GE Washer Leaking, Noisy, or Drum Damaged? Inner Tub Assembly Kit WG04F11975 – Complete OEM Tub Rebuild A cracked tub, damaged basket, or failed tub gasket is one of the most serious failures in a GE washer — and a full inner tub assembly kit is the correct fix when multiple tub components are compromised. In GE front-load and top-load washers, the inner tub assembly consists of the spin basket, front and rear tub halves, and the tub-to-basket gasket seal. When any of these components crack, warp, or fail, the result is water leaks, excessive vibration, drum noise, or complete loss of spin function. ⚡ Common failure point in GE-built washers after high-impact loads, bearing failure, or long-term wear. This kit (lead part WG04F11975) is the complete OEM replacement that restores the full inner tub assembly to factory specification in a single repair. ❓ Is This the Right Part? This is the correct fix if ALL of the following are true: ✔ The washer powers on and the control panel functions normally ✔ Water supply and drain hoses are confirmed undamaged ✔ The outer tub (cabinet shell) is undamaged ✔ ONLY problem is a cracked basket, leaking tub, drum noise, or failed tub seal Not sure? Send us your model number — we’ll confirm compatibility before you order. 🔧 Common Symptoms Water leaking from the bottom or front of the washer during a cycle Loud banging, grinding, or rumbling during the spin cycle Visible cracks or holes in the wash basket or tub Drum wobbles excessively or contacts the outer tub during spin Washer stops mid-cycle due to imbalance or tub damage Mold or odour from a failed tub gasket that no longer seals properly ✔ If these symptoms match, this complete tub kit is the correct repair solution. ✔ Replacing the full inner tub assembly restores proper sealing, balance, and spin function immediately. 📦 Kit Contents & Part Details Basket: WG04F11975 — Inner spin basket (primary drum) Rear Tub: WG04F11961 — Rear tub half housing Front Tub: WG04L06847 — Front tub half housing Gasket: WG04L06826 — Tub-to-basket seal gasket Type: Complete Inner Tub Assembly Kit — OEM GE replacement Brands: GE ⚠️ Recommended While Repairing: If you’re rebuilding the inner tub, this is the ideal time to replace the tub bearing and bearing seal — worn bearings are often the root cause of the drum damage in the first place, and replacing them now prevents the new tub assembly from failing prematurely. Also inspect the drive belt and motor coupling for wear while the tub is disassembled. ⚙️ Installation Skill Level: Advanced — 2–4 hours. Disconnect power and water supply before servicing. Full inner tub replacement requires disassembling the washer cabinet, removing the outer tub, separating the front and rear tub halves, transferring the spin basket, and reassembling with the new gasket seal. This is a major repair — photograph all harness and hose connections before disconnecting. Professional installation is recommended if you are not experienced with washer disassembly. ✓ Compatible Models Confirmed compatible with select GE washer models. Contact us to verify your model number before ordering — tub assemblies are model-specific and must be confirmed before purchase. 💡 Pro Tip Replace the Bearing While You’re In There: The tub bearing sits between the inner basket and the rear tub — and if your basket or tub is damaged, there’s a high probability the bearing is worn too. Bearing failure causes the basket to wobble and contact the tub, which is often what causes the tub damage in the first place. Replacing the bearing at the same time as this kit adds 30 minutes to the job but eliminates the most common reason a rebuilt tub assembly fails within a year.