Driver Bucket Seat with Inner Armrest Provision & Map Pocket – Seat Cover for Ford Transit Custom V710

Seat Cover for Driver Bucket Seat with Inner Armrest Provision & Map Pocket (Airbag Compatible) For Ford Transit Custom V710 Suits: 2025 Ford Transit VO Custom SWB Dual Cab Single Cab Van Available in Canvas in Black or Grey and 4Elements in Black. Our heavy-duty canvas and 4Elements seat covers are made in Australia using Australian-made materials developed specifically for the harsh Australian climate. With manufacturing facilities in WA. Please note these are manufactured to order so have an approx. leadtime of 4 weeks 4Elements 4Elements by Black Duck® SeatCovers is tested to withstand tough conditions without compromising on comfort. Featuring a 19.2oz Cotton Twill Composite, this is a heavyweight product with a soft and flexible feel for the ultimate in seat protection. Made from a 100% waterproof material that is also machine washable to keep your vehicle seats in pristine condition – you won’t be disappointed! Features 19.2 oz Cotton Twill Composite Hard Wearing Protection 100% Waterproof Material Soft and Flexible Washable UV Resistant Tailored Fit for Comfort and Style Air-bag Compatible Exclusive to Black Duck Available in Black Heavy-duty Canvas Heavy-duty Canvas by Black Duck® SeatCovers has undergone rigorous testing to ensure it meets stringent Australian Standards for strength and endurance. Our Canvas is treated using advanced technologies to ensure resistance to water, rot and mildew - for vehicles that work and play hard! Features 14.9oz Military Grade Canvas Heavy-Duty Protection 24+ Hour Water Resistance Rot and Mildew Resistant UV Resistant Tailored Fit for Comfort and Style Air-bag Compatible Available in our standard colours Grey, Black Care and Cleaning: Gentle, cold machine wash (<30C) Lay flat to dry Ensure the seat covers are fully dry before placing on vehicle seats DO NOT tumble dry DO NOT dry clean DO NOT use detergent DO NOT use bleach DO NOT iron Fitting Instructions: Our seat covers go through a rigorous design process to ensure they not only offer a tailored fit to your specific seat design, but they are also designed to be as simple as possible to fit. To start We recommend unpacking each seat separately to avoid mixing up the driver, passenger and rear seat parts. Remove the covers from the packaging and lay them out to check that you have all the correct parts. You should have: Seat base Backrest (sometimes base and back are attached) Headrest Armrest (if applicable) Each piece is identified on the inside with a white label. On the Driver and Passenger seat label, there will be a ‘DR’ to indicate Driver and a ‘PA’ to indicate Passenger. If you have seat fitted air-bags, the teal AIRBAG label will go on the outside/window side of the seat Vacuum your original seats and remove anything from the seat pockets. Fitting the seat base: Slide the cover over the seat base, ensuring it is clear from any levers and buttons, line up the seams of the cover to the seams of the seat and massage into place Once the cover is in line with the seams of the seat, push the centre flap through the seat base until you can see it pop out the back of your seat. (In some models you may need to detach the carpet on the back of your seat to allow access) Pull the side flaps around and attach to the centre flap. Check to make sure none of the seat's levers and buttons is obstructed If included in the seat cover design, pull straps under the seat, clearing all tracks and fittings. Pull tight and fasten to the opposite side – test movement of seat to ensure nothing is obstructed Seat base fitting complete Fitting the backrest: Remove headrest (if applicable) Slide cover over the top (like a jumper), make sure the back of the cover does not catch in the pocket on the back Line up the seams of the cover to the seams of the seat and massage into place Push the flap through the base of the seat, just like you did with the base Pull through tight and attach to the back of the seat Slide the headrest cover over the headrest with the label on the front and secure the flaps. This is designed to be a tight fit so make sure you have the seams lined up Replace the headrest. Backrest fitting complete Repeat this process for the passenger seat and rear seats. Once you have had your covers for a couple of weeks, we advise that you re-tension them as they will mould to the shape of your seat over time. This will leave you with the best fit possible. **WARNING** Only Black Duck SeatCovers that are labelled as being air-bag compatible are to be fitted to vehicles with seat fitted air-bags. Black Duck SeatCovers must not be fitted to seats containing side-impact airbag components unless they are the correct seat covers with the appropriate certification. Black Duck SeatCovers accepts no responsibility or liability if this warning is not adhered to.