1500MM Heavy Duty Linear Actuator C One-Control-Eight Synchronous Control Kit (Model 0043108-3)

This one-control-eight synchronous kit is used for heavy-duty linear actuators to synchronize their operation. The kit includes eight Type-C heavy-duty linear actuators with built-in Hall effect sensors, two four-channel synchronous controllers (one master controller and one slave controller), one touch control handle, and a CH-3 remote control. Note: All linear actuators must be connected to the synchronous controller for the system to function properly. Application: Mainly used for doors, windows, cellars, trapdoors, hatchways, solar tracking system, medical devices, agricultural machinery, vehicles, ships, elevator platforms, lifting tables, TV lifts, robots, cabinetries, massage sofas, electric beds, medical chairs, and other electrical equipment. It can open, close, push, pull, lift, and descend these devices. It can replace hydraulic and pneumatic products to save power consumption. The Information for Electric Linear Actuator The stroke range of linear actuators is 60 ~ 80 inches or 1500 ~ 2000 mm. We can also customize any stroke length from 1500mm to 2000mm, such as 1650 mm, 1750 mm, 1850 mm and so on. If you want to view detailed information of linear actuators with different strokes, such as detailed drawings and dimensional drawings, please click the following link to view: 1500MM [60 in] Actuator Key Features High-quality products and high-quality services Metal housing, able to work in very harsh environments Metal gearbox and high strength wear-resistant metal gears Stainless steel telescopic tube and outer tube, good corrosion resistant Heavy duty design, high-power DC motor Strong thrust, up to 3000 N / 300 kg / 670 lbs at 20mm/s Two speed options: 20±4mm/s, 50±10mm/s Multiple stroke options, from 1500 mm to 2000 mm Advanced waterproof and dustproof technology Low power consumption and low noise Built-in clutch to protect gears and motors Built-in motor overload and overheat protection Built-in two limit switches, linear actuator will automatically stop when stroke rod reaches the limit position Built-in Hall sensor, so you can use the synchronous controller to operate 2, 4 or more linear actuators fully synchronously Manual operating device is optional, allowing you to extend or retract the telescopic rod of the linear actuator with hand tools The front and rear connector style can be customized: the default is an open hole connector, which can be customized with slotted connector, internal thread connector, etc. And you can provide drawings for customization The orientation of the front and rear connectors is default; we can rotate them 90 degrees during the production according to the customer's needs With auto-locking capability to hold load position after stopping, and no power supply is required Maintenance-free Specifications Parameter Value Working Voltage DC 12V, DC 24V, DC 36V or DC 48V (24V most commonly used) Stroke Range 60 ~ 80 inches or 1500 ~ 2000 mm Optional Speed (No-load) 20±4mm/s, 50±10mm/s (The actual working speed will gradually slow down as the load increases.) Max Load Capacity 3000 N / 300 kg / 670 lbs at 20mm/s (Linear actuator can get maximum load capacity when it operates in the vertical direction, and the pulling force is less than pushing force.) No-load Current 2~3A at 12V or 1~1.5A at 24V Full Load Current 12~20A at 12V or 6~10A at 24V Recommended Power Supply 12V/166.6A or 24V/83.3A Shaft Diameter 28mm [1.102 in] Front / Rear Connector Mounting Hole Diameter 13mm [0.512 in] Housing Material Stainless steel Stroke Rod Material Stainless steel Gear Material Steel Alloy Motor Type Brushed DC Motor Duty Cycle 10%, max 2mins continuous use Service Life approx. 35, 000 cycles Power Cable (Plug Standard) Six-pin Plug Linear Actuator Cable Length 2500±10%mm [98 in] (The length can also be customized according to your specific needs.) Certifications CE Environment Temperature -26℃ to 85℃ Operating Noise about 56dB~66dB (Linear actuators with different parameters will have different noise levels.) IP Rating IP65 Different Speeds and Corresponding Maximum Thrust No-load Speed Full load Speed Maximum Thrust Self-locking Force 20mm/s 15mm/s 3000 N / 300 kg / 670 lbs 3500 N / 350 kg / 790 lbs 50mm/s 38mm/s 1000 N / 100 kg / 200 lbs 1500 N / 150 kg / 340 lbs Note: 1. The above data is the maximum load capacity that can be obtained when each linear actuator runs in the vertical direction. The maximum load capacity of the entire synchronous system is the sum of the maximum load capacities of the eight linear actuators. If the weight of your equipment (such as a cellar door) is 100kg, and you want to use a linear actuator to open this door, you need to calculate the actual force acting on the linear actuator according to your installation method. This force is usually 2-5 times the weight of the cellar door. If you don't know how to calculate it, please contact us for help. 2. The above is the speed at no load, and the actual working speed will gradually slow down as the load increases. Full load speed is approximately 60-70% of No-load speed. 3. Different speeds correspond to different maximum loads. Please select the right speed according to the speed and maximum load you need. 4. Linear actuators are not recommended for continuous operation under maximum load, we recommend letting it work at about half of the maximum load to get a longer working life. 5. For linear actuators with a stroke greater than 500MM, you should not normally allow them to operate at their maximum stroke under heavy loads. If the actual stroke you want is 600MM, we recommend that you choose a linear actuator with a stroke of 700-800MM. 6. The maximum pull force of the linear actuator is slightly less than its maximum thrust force. Installed Length and Stroke Customization The linear actuator has two built-in limit switches, When the linear actuator is fully retracted or fully extended, it will stop automatically. We can adjust the position of the built-in limit switches during production to meet customer-specified stroke and retraction lengths. Example for a linear actuator with a 1500 mm stroke: Retraction Length: 1850 mm (center distance between two mounting holes when the linear actuator is fully retracted) Extension Length: 3350 mm (center distance between two mounting holes when the linear actuator is fully extended) Custom Rules: 1) The specified stroke must be less than the standard stroke of the ordered actuator. For example, a specified stroke of 1450 mm is less than the standard stroke of the ordered actuator (1500 mm). In this case, the retraction length will be reduced by an equivalent value, resulting in a retraction length of 1800 mm. Of course, you can also choose to retain the original standard retraction length of 1850 mm. 2) The specified retraction length must be less than the standard retraction length of the ordered actuator. For example, a specified retraction length of 1750 mm is less than the standard retraction length of the ordered actuator (1850 mm). In this case, the stroke must also be reduced by an equivalent value, resulting in an effective stroke of 1400 mm. Note: This is a synchronous control kit for eight linear actuators. The quantity of customization options for installed length and stroke length ordered must match the quantity of actuators ordered., i.e., also eight. The Information for Synchronous Controller Introduction If you want to use multiple linear actuators to raise and lower an equipment, for example two, four or more electric actuators. Since the high-speed DC motors in electric actuators cannot run at exactly the same speed, so the movement speed of the electric actuator will also be different. When multiple electric actuators work at the same time, their actual speeds cannot be exactly the same. In this case, we can use a synchronous controller to operate multiple linear actuators to rise or fall synchronously. They work completely in sync without any difference. Working Principle If you want to use a synchronization controller to operate two or more linear actuators fully synchronously, you will need to add built-in Hall effect sensors for each linear actuator. And when you purchase Hall effect sensors along with linear actuators, we will install Hall effect sensors in the linear actuators during production for you. When two or more linear actuators are running together, Hall sensor will send Hall signals to the synchronization controller, and the controller will adjust the running speed of each linear actuator, so that all linear actuators run at the exact same speed. Key Features It can operate eight electric linear actuators C to run completely synchronously Wired control via a touch control handle Wireless control via a remote The LED display on the control handle and remote control will display the stroke position in real time Six touch function buttons: ▲, ▼, 1, 2, 3 and R (Buttons ▲ and ▼ are used to operate the linear actuators extension and retraction; buttons 1, 2 and 3 are used to automatically operate the linear actuators to three pre-memorized positions; button R is the reset button and is used to reset the system in case of an error) With reset button When linear actuators move close to the end position, they will automatically slow down to protect themselves When linear actuators are fully retracted, they will retain 1MM of travel to protect themselves Controller Specifications Parameter Value Operating Voltage 12~48 VDC, suitable for 12V or 24V linear actuator Number of Connecting Linear Actuators 8 Working Frequency 2.4 GHz Working Distance 10m / 30ft (theoretically) Rated Current 25A Two Selectable Control Modes Interlocking Mode or Momentary Mode Operating Temperature -20°C ~ +70°C Case Size 155 x 150 x 52 mm (6.1 x 5.9 x 2.0 inches) Cable Length of the Touch Control Handle 2000±10%MM [80 in] (If you need a longer cable, please purchase the control handle extension cable) Connection 1) Use signal lines to connect the CAN-L and CAN-H terminals of the master controller to the CAN-L and CAN-H terminals of the slave controller. 2) Plug the touch control handle into the Hand Set port of the master controller. (Note: If the control handle is plugged into the Hand Set port of the slave controller, it will not function.) 3) As shown in the diagram, connect four linear actuators to channels CH1, CH2, CH3, and CH4 on the master controller, and then connect the remaining four linear actuators to channels CH1, CH2, CH3, and CH4 on the slave controller. Be sure to insert two terminals of each actuator into the corresponding two ports of each channel. 4) Connect the positive pole of DC power supply to the terminal <+> of the two controllers, and connect the negative pole of DC power supply to the terminal <-> of the two controllers. How to Set the Control Mode The controller has two selectable control modes, interlocking mode and momentary mode. You can switch the control modes as follows: Press the pairing button on the controller three times in a row. Operation 1. Operation via the touch control handle: Attention: The handle is operated by touch control. The touch sensitivity can be automatically calibrated when powered on for the first time. Hands are prohibited from touching the handle when powered on to prevent interference with the sensitivity calibration and affect the operating sensitivity. 1) Press and hold the ▲ button of the control handle, all linear actuators extend outward at the same time; Release the button, all linear actuators stop at the same time. 2) Press and hold the ▼ button of the control handle, all linear actuators retract inward at the same time; Release the button, all linear actuators stop at the same time. 3) Press any button 1, 2, or 3 on the control handle, all linear actuators will automatically move to the position memorized by that button and then automatically stop. Note: You will need to first memorize three positions into these three buttons. 4) The LED display on the control handle will display the stroke position data in real time. For example, the number 03.5 means that the linear actuators have reached the stroke position of 35MM. 2. Operation via remote control: 2.1 When the controller is operating in momentary control mode: 1) Press and hold the button ▲ of the remote control, all linear actuators extend out at the same time; Release the button, all linear actuators stop at the same time. 2) Press and hold the button ▼ of the remote control, all linear actuators retract inward at the same time; Release the button, all linear actuators stop at the same time. 2.2 When the controller is operating in interlocking control mode: 1) Press the button ▲ of the remote control, all linear actuators extend out at the same time, they will reach the maximum stroke at the same time and stop automatically. 2) Press the button ▼ of the remote control, all linear actuators retract inward at the same time, they will fully retract at the same time and stop automatically. 3) During operation, you can press the stop button or any button of the remote control to stop all linear actuators at the same time. The LED display on the remote control will display the real time stroke position data of the linear actuators. For example, if the LED display shows UP 29.5 cm, it means the linear actuators has been extended to the stroke position of 295mm, or if it shows DN 20.0 cm, it means the linear actuators has been retracted to the stroke position of 200mm. How to Memorize three Stroke Positions 1) The controller can memorize total three stroke positions, and each button memorizes one stroke position. 2) First operate eight linear actuators to the first suitable stroke position that you need to store, then press and hold the button 1 of the control handle for about 5-6 seconds, the stroke value on the LED display will flash twice. This means that the current stroke position is already stored in button 1. 3) You can continue to store the other two stroke positions into the button 2 and 3 by following the operation above. Reset Function When the LED display on the control handle shows the fault code, you need to reset the system as follows. Reset operation: Press and hold the <R> button of the control handle or the <Reset> button on the master controller, until all linear actuators are reset to the bottom, and the LED display on the control handle shows "00.0", then release the button. How to Pair the Remote Control to the Controller Notice: We have paired the remote control to the controller before leaving the factory. If you want to pair more remote controls, please follow the following steps. 1) Press and hold the pairing button on the master controller for 5-6 seconds, until the green LED flashes quickly, this indicates that the controller enters the learning status. 2) Press the ▲ and ▼ buttons of the remote control 5 times in a row. The CH position on the remote control's LED display will change from -- to 00, gradually increase, and finally change to -- again, and the controller will automatically exit the pairing state, this indicates that the pairing is successful. 3) The controller can learn multiple remote controls with different codes. Fixed Bracket and Accessories 1. Each linear actuator would require two mounting brackets , one to fix the head of linear actuator and another to fix the bottom of linear actuator. This kit does not contain fixed mounting brackets, please buy them from the drop down menu. 2. Compatible Mounting Bracket: Bracket G . 3. This linear actuator is also compatible with two flat mounting brackets: Head Fixed Mount Circular Disk Bracket (Model 0043075) and Bottom Fixed Mount Flat Bracket (Model 0043076) . 4. The front and rear connector style of the linear actuator can be customized: the default is an open hole connector, which can be customized with slotted connector, internal thread connector, etc. And you can provide drawings for customization. If you need customization, please click front connector style and rear connector style to purchase the customized option. (The quantity of front and rear connector styles ordered must match the quantity of actuators ordered.) 5. Linear actuator fisheye connector can be customized and used in conjunction with the internal thread connector. If you need customization, please click here to purchase the customized option. (The quantity of fisheye connectors ordered must match the quantity of style 2 connectors ordered.) 6. The orientation of the front and rear connectors of the linear actuator is default; we can rotate them 90 degrees during the production according to the customer's needs. If you need to rotate the connectors 90 degrees, click here to purchase the rotation option.(The quantity of 90-degree rotating connector options ordered must match the quantity of actuators ordered.) 7. The linear actuator can be equipped with a manual operating device. Even in the event of a power outage, it is possible to extend or retract its telescopic rod using hand tools. If you need a manual operating device to equip the actuator, please click here to purchase it. (The quantity of manual operating devices ordered must match the quantity of actuators ordered.) Production Time & Return or Exchange Policy The linear actuators are customized and not in stock, and we need to spend 3~7 working days to produce them according to the specified parameters in your order, so that we don't accept returns or cancel orders. If customers order unsuitable linear actuators themselves, we also do not accept exchanges, please understand. Click to Download 3D CAD Model Files in STEP format 1500MM [60 in] Actuator Package Include 8 x Electric Linear Actuator C with Hall Effekt Sensor 2 x Four-Channel Synchronous Controller (One master controller and one slave controller, One-Control-Eight, For 8 Linear Actuators C) 1 x Touch Control Handle 1 x Remote Control (CH-3) 1 x User manual