TOTA | Fletched Hunting Arrows | Non-Woven | .166” | 4mm

Meet The Arrow — .166 Meet The Arrow — Tooth of the Arrow’s premium .166” diameter carbon hunting arrow, built for maximum penetration, speed, and downrange efficiency. Designed with a micro diameter profile and lightweight non-woven carbon construction, this shaft is built to cut through wind and drive deep. Built for hunters. Trusted by shooters. These shafts don’t just fly — they hit hard. Our Recommendation: Best suited for intermediate to advanced bowhunters looking for increased penetration and improved wind performance. Arrows come cut to length and prefletched. Customers must install inserts. For Hunters: Ideal for deer, antelope, and other medium game where penetration and accuracy matter most — especially in mid to long-range shots (30–80+ yards). Tech Specs – .166” | 4mm Carbon Hunting Arrows Material: Non-woven carbon fiber Inner Diameter (in): 0.166” Outer Diameter (in): 0.258” (250), 0.256” (300), 0.247” (350), 0.241” (400) Straightness Tolerance: ± 0.003” Spine Options: 250, 300, 350, 400 GPI (grains per inch): 12 (250), 10.0 (300), 9.4 (350), 9.2 (400) Length Options (in): Cut to order in 0.25” increments Fletching: 3 × 2.0” Blazer vanes, right 1.5° helical Nocks: Standard white .166 nock Insert / Half-Out: Included loose (specify weight + material if known) Weight Tolerance: ± 2 grains These premium .166” carbon arrows are built from non-woven carbon fiber, delivering a lightweight, high-speed shaft with a tight ±0.003” straightness tolerance. Their micro diameter design reduces wind drift and increases penetration, making them ideal for hunters looking to maximize downrange performance. Each shaft is cut to length in 0.25” increments, prefletched, and includes components for custom installation, giving you full control over your build. Features .166” / 4mm Micro Diameter – Less wind drift. Deeper penetration. Better energy retention downrange. Lightweight Carbon Construction – Built for speed without sacrificing performance. Non-Woven Carbon Build – Straight fiber alignment for consistency, weight savings, and clean performance. Spine Options – Multiple spine offerings for proper tuning across setups. Tolerances – ±0.003” straightness and ±2 grain weight tolerance for consistency shot after shot. Components – Includes inserts/half-outs and white Signature Nocks (loose for install). Vanes – All arrows come prefletched with 3 × 2.0” Blazer Vanes. Length Options – Free arrow cutting to your desired length. Standard nock adds 0.25”, insert/half-out adds 1.00”. If you are not sure which shaft is best for you, please reach out to us at customercare@toothofthearrowbroadheads.com and review our spine selector tool. Before use, review all safety instructions. What’s Included Each pack of The Arrow .166” Carbon Hunting Arrows includes: 6, 12, or 24 premium prefletched shafts (choose your quantity) All shafts cut to your specified length White .166 nocks, included Inserts / half-outs, included loose for custom installation 3 × 2.0” Blazer vanes, right 1.5° helical FAQ Q: Do these shafts come fletched or bare? A: By default, these shafts are sold prefletched and cut to your requested length. White .166 nocks and components are included. We also offer bare shaft options for the DIY bowhunter. Q: How do I choose the correct spine? A: Spine depends on draw weight, arrow length, and point weight. Use our Spine Selector Tool or email us at customercare@toothofthearrowbroadheads.com and we’ll help you dial it in. Q: Will you cut the arrows to my length? A: Yes. We offer free arrow cutting in 0.25″ increments. The nock adds 0.25″ and the insert/half-out adds ~01.00″ to total length. Q: Are these compatible with standard .166 components? A: Yes. These shafts use a .166″ (4 mm) inner diameter and are compatible with most .166 ID components. Included components are designed for a precise fit. Q: What tolerances can I expect? A: All shafts are built to ±0.003″ straightness and ±2 grain weight tolerance. Q: What’s your return policy on cut shafts? A: Cut shafts are non-returnable unless there’s a manufacturing defect. Uncut shafts can be returned if unused and in original packaging. Q: Can these be used for both hunting and target shooting? A: Absolutely. The .166″ micro diameter improves penetration and wind performance for hunting, while tight tolerances make them excellent for target and 3D shooting.