Dandy 2-Speed Electric Powder Trickler

MADE TO ORDER - 1 Week for build time Made in the USA • Precision Reloading Fine control for the final approach. Move powder quickly with the fast control, slow the flow as the scale approaches your target, and fine-tune delivery for controlled, kernel-by-kernel dispensing. 2X Fast + slow control Use the red fast button for larger additions and the yellow slow button as the target charge approaches. • Adjustable powder flow A sliding tube weight lets you tune powder movement for the propellant and precision your setup requires. 360° Fits the way you work Adjust height, rotation, and reach to position the outlet around many beam and electronic scale layouts. Controlled, hands-on precision More control than a manual trickler—without a fully automated system. Precision handloading often comes down to the last few kernels. The Dandy 2-Speed Electric Powder Trickler gives you direct control over that final approach while letting you use the beam or electronic scale you already trust. Start with the fast button when the pan needs a larger addition. As the display or beam nears the target weight, move to slow and adjust the sliding weight on the discharge tube. When properly configured for the powder in use, the Dandy can dispense in controlled, kernel-by-kernel increments. Designed around your bench 1–5.5 in Adjustable outlet height Up to 6 in Stated reach from the base 24 in Remote control cable ~1,000 gr Approximate hopper capacity Purpose-built details Angle-cut outlet See powder at the end of the 4.25-inch discharge tube. Weighted base Provides a substantial, stable foundation on the bench. Stainless-steel tower rod Supports adjustable height and rotational placement. Knurled steel lock Secures the selected hopper position without complicated setup. Cordless AA power Runs on two AA batteries, with no outlet or adapter required. Independent operation Use it with a compatible scale of your choice; no proprietary scale required. Specifications Operating method Battery-powered vibratory trickling Controls Slow/yellow and fast/red Fine adjustment Sliding discharge-tube weight Hopper capacity Approximately 1,000 grains Height adjustment 1–5.5 in, measured to tube center Rotation and reach 360°; up to 6 in from base Discharge tube 4.25 in with angle-cut outlet Control cable 24 in Power 2 AA batteries, not included Compatible propellant Smokeless powder only Country of origin USA What’s included Dandy 2-Speed Electric Powder Trickler assembly Hopper assembly Weighted base, tower rod, and locking nut Two-button control pad with 24-inch cable Sold separately Two AA batteries Reloading scale and scale pan Smokeless powder Powder measure and other pictured equipment Simple setup Slide the hopper assembly onto the tower rod and secure it at the desired height and angle. Install two AA batteries in the control pad. Position the discharge tube above the scale pan without touching the scale. Add the appropriate smokeless powder to the clean hopper. Use fast speed for larger additions, then slow speed and the sliding weight near the target. Empty and thoroughly clean the hopper and powder path before changing powders. Important safety warning For smokeless powder only. Do not use black powder or black-powder substitutes. Static discharge can ignite black powder. Keep powder away from heat, sparks, flame, and other ignition sources. Do not leave powder in the hopper after a loading session. Verify every charge on a suitable scale and always follow current published load data and established safe-reloading practices. Frequently asked questions Does it include a scale? No. This is a standalone powder trickler for use with a separate beam or electronic reloading scale. The scale and scale pan are sold separately. Can it dispense one kernel at a time? It can be adjusted for controlled, kernel-by-kernel dispensing. Actual flow depends on powder geometry, hopper position, sliding-weight position, and scale response, so tune the setup whenever the powder changes. Does it replace a powder measure? It is optimized for bringing an undercharge up to its target weight. Many reloaders use a separate measure or scoop for the initial safe undercharge and the Dandy for the final controlled addition. Will it work with an electronic scale? It is designed to work around many beam and electronic scale layouts. Fit depends on the platform and pan location; use the adjustable height, rotation, and reach to align the outlet without touching the scale.