Cisco WS-C2960X-48FPS-L 48-Port GbE PoE+ 740W Switch + FlexStack Module | Wty

Cisco Catalyst WS-C2960X-48FPS-L — 48-Port Gigabit PoE+ Managed Switch A 48-port Layer 2 managed switch with PoE+ on every port, a 740W power budget, four 1G SFP fibre uplinks and FlexStack-Plus stacking. Supplied with the FlexStack-Plus stacking module and backed by a 12-month Reboot IT warranty. Key Benefits 48 Gigabit PoE+ ports: every port delivers up to 30W (802.3at), so phones, access points and cameras run on one cable. 740W power budget: enough headroom to power a full floor of devices from a single rack unit. 4 x 1G SFP fibre uplinks: reach beyond copper distance between floors, buildings or back to the core. FlexStack-Plus module included: stack up to eight switches as one logical unit with a single IP and one configuration. LAN Base Layer 2 management: VLANs, QoS and port security via web GUI or Cisco CLI. Rack-mountable 1U chassis: standard 19-inch mounting for comms cabinets and racks. Performance In Use The 2960-X sits at the access layer, where endpoints plug in. With PoE+ across all 48 ports and a 740W budget, it powers IP handsets, wireless access points and most fixed and PTZ cameras directly — removing separate injectors and giving you one place to power-cycle a device remotely. The four SFP slots take fibre transceivers for links that exceed the 100-metre copper limit, so the uplink to the core or to another building does not consume any of the 48 copper ports. LAN Base management adds VLAN segmentation, QoS prioritisation for voice traffic, and port security — configured through the web interface or the Cisco CLI. Because the FlexStack-Plus module is included, expansion does not mean added complexity: additional 2960-X switches join the stack and are administered as a single device with one IP address and one configuration file. Technical Specifications Model Cisco Catalyst WS-C2960X-48FPS-L Ports 48 x 10/100/1000 Gigabit Ethernet (RJ-45) PoE PoE+ (IEEE 802.3at) on all 48 ports, 740W total budget Uplinks 4 x 1G SFP Stacking FlexStack-Plus, up to 8 switches (module included) Feature Set LAN Base (Layer 2) Management Web GUI and Cisco CLI; VLANs, QoS, port security Form Factor Rack-mountable, 1U Warranty 12 months (Reboot IT) Is It Right For You? Best For ✓ • Powering IP phones, access points and cameras • Office or floor access-layer switching • Sites needing fibre uplinks to a core switch • Networks expected to grow — stack up to 8 • VLAN segmentation and voice QoS Not For ✗ • Layer 3 routing between subnets (LAN Base is Layer 2) • 10G uplink requirements — these are 1G SFP • Multi-gigabit access ports (2.5G/5G) • Silent environments — this is a fan-cooled rack switch • Deployments needing current-generation vendor support Condition Grades Grade Cosmetic Condition A — Excellent Minimal marks. Light scratches or rack-ear wear possible; fully tested and functional. B — Good Light to moderate wear consistent with rack use — scuffs, marks or faded labelling. Fully tested and functional. All units are wiped to factory defaults, powered up and port-tested before dispatch. Frequently Asked Questions How many devices can it power over PoE? All 48 ports support PoE+ up to 30W each, sharing a 740W total budget. In practice that powers roughly 24 devices at full 30W, or all 48 at typical phone and access-point draw. Is the FlexStack module included? Yes. The FlexStack-Plus stacking module ships with this unit, so it can be stacked with other 2960-X switches out of the box. Are SFP transceivers included? No. The four SFP slots are supplied empty — transceivers are chosen to match your fibre type and distance. Can it route between VLANs? Not fully. LAN Base is a Layer 2 feature set: it creates and segments VLANs, but routing between them requires a Layer 3 switch or router. What is supplied in the box? The switch, the FlexStack-Plus stacking module, a power cable and a tax invoice. What warranty is included? Every unit carries a 12-month warranty from Reboot IT, covering hardware faults in normal use. Support is handled locally in Melbourne. How is it shipped? Shipping costs apply based on size and destination — rates are calculated at checkout. Is it configured or reset? Every unit is wiped to factory defaults so you can apply your own configuration from the first boot. Warranty & Support This switch is covered by a 12-month Reboot IT warranty. Reboot IT has refurbished business IT in Melbourne since 2001 — every unit is tested, wiped and graded before it is listed, and supported by a local team after it ships. Shipping costs apply based on size and destination and are calculated at checkout. Reboot IT — reboot-it.com.au — Melbourne, since 2001.