Trak Racer TR Series GT Racing Seat (Dry Carbon Fibre)

Trak Racer TR Series GT Racing Seat (Dry Carbon Fibre) A fixed-back GT bucket seat in genuine motorsport-grade carbon fibre, and the strongest seat in the Trak Racer range at a 200kg weight capacity. That figure is the headline: most sim seats stop at 160kg, so this is the one that suits larger drivers without qualification. The driving position is straight GT rather than hybrid, which makes it the right choice if you race grand touring, endurance and rally rather than open-wheel. Deep side bolsters handle heavy braking and fast direction changes, and the padding is high-density foam under breathable, washable, fire-retardant trim. It fits S to XL drivers up to roughly 42 to 46 inches at the waist, mounts side-on with standard M8 29.5mm spacing, and takes 4, 5 and 6-point harnesses. It sits at the top of the racing seats range. Key features Genuine motorsport-grade carbon fibre shell GT driving position Fits S to XL, waist up to 42 to 46 inches Rated to 200kg, 440lb High-density foam padding Breathable washable fire-retardant trim Side mount, standard M8 29.5mm spacing 4, 5 and 6-point harness ready Where the 200kg rating comes from Carbon fibre has a better strength-to-weight ratio than fibreglass, and on this seat Trak Racer has spent that advantage on capacity rather than lightness. The result is a 200kg rating against the 160kg of the hydro-dipped fibreglass seats in the range. That matters in two situations. If you are a larger driver, it is the difference between a seat rated for you and one you are hoping about. And if you run a commercial rig, an esports venue or a training facility where you cannot control who sits in it, the extra margin is the responsible specification. Pair it with a chassis from the aluminium chassis range that can carry the load. Genuine carbon against the carbon-look seats Two seats in this range wear a carbon weave without being carbon: the GT Pro and the RS GT Rally-Pro both use a hydro-dipped fibreglass shell. They look the part and cost considerably less. This one is the real thing. The case for genuine carbon is rigidity per kilogram, which matters most on a motion platform where the actuators have to move the seat and driver together. Less mass means the cue arrives when the software sent it rather than a fraction later. On a static rig the difference is far smaller, so be honest about your build before paying for it. The motion simulators range is where the difference shows. Frequently asked questions Is the carbon fibre genuine?Yes. The shell is genuine motorsport-grade carbon fibre, not a carbon-look finish over fibreglass.What is the weight capacity?200kg, 440lb, which is the highest in the Trak Racer seat range.Is the position GT or Formula?Straight GT. The HCF Hybrid Formula seat is the one that covers a Formula recline as well.Does it take harnesses and sliders?Yes to 4, 5 and 6-point harnesses. Seat sliders and side brackets are sold separately, in the hardware mounts range. Specifications Part number: SA-16 Type: Fixed-back carbon fibre GT racing bucket seat Construction: Genuine motorsport-grade carbon fibre shell Driving position: GT Fit range: S to XL, waist up to approximately 42 to 46 inches Weight capacity: 200kg, 440lb Padding: High-density foam Upholstery: Breathable, washable, fire-retardant trim Stitching: Double stitched, high-strength nylon thread, reinforced wear areas Mounting: Side mount, standard M8 29.5mm spacing Harness: 4, 5 and 6-point compatible Sliders and side brackets: Sold separately Compatible frames: RS6, TR8 PRO, TRX, Porsche 91XTR, TR200, TRA, TR160, TR120, TR80S, TR40S, TRK and other branded rigs Motion support: D-BOX, Sigma Integrale and Qubic Systems, subject to cockpit and platform configuration Warranty: Shell 2 years, upholstery 1 year What's In The Box? 1x Fixed-back carbon fibre GT bucket seat High-density foam padding, fitted Breathable fire-retardant upholstery, fitted Integrated side bolsters Side mount hardware, M8 at 29.5mm spacing Reviews Warranty This Trak Racer seat carries a two-part manufacturer warranty. The genuine carbon fibre shell is covered for 2 years against defects in materials and manufacturing under standard residential use, and the upholstery and stitching are covered for 1 year. Normal wear, marks, scratches, accidental damage and misuse sit outside the warranty. Every product is 100% genuine, sourced directly from Trak Racer's official distributors, and our Australian simulation team is only a call or email away.