DSTIKE ESP32 Walkie-Talkie Speaker — ESP-NOW Receiver

Receive-Only Speaker for the DSTIKE ESP32 Walkie-Talkie The DSTIKE ESP32 Walkie-Talkie Speaker is a compact, USB-powered wireless receiver designed as a companion to the DSTIKE ESP32 Walkie-Talkie. It receives digital voice transmissions from a compatible DSTIKE device over ESP-NOW and plays them through an integrated 4Ω/3W speaker. No Wi-Fi router, internet connection, SIM card or mobile service is required. Important: This is a receive-only device. It does not contain a microphone or PTT button and cannot transmit voice or reply to the sender. A compatible transmitting device is required and sold separately. Key Features ESP32-WROOM-DA main controller ESP-NOW digital audio reception Receive-only operation No Wi-Fi router or internet connection required Reception range up to approximately 150 meters in suitable open conditions 10 preset channels Compatible with the DSTIKE ESP32 Walkie-Talkie Integrated 4Ω/3W speaker Green and blue status indicator Recessed channel-selection button Continuous 5V USB-A power Compact 3D-printed enclosure Fully assembled and ready to use Open-source schematic and firmware Reprogrammable for custom ESP32 projects How It Works The receiver listens for compatible ESP-NOW voice transmissions on the selected preset channel. When a matching DSTIKE Walkie-Talkie transmits, the speaker receives the digital audio data and plays the voice message through its integrated speaker. When the transmission ends, it returns to standby. The transmitting walkie-talkie and receive-only speaker must: Use compatible DSTIKE firmware Use the same ESP-NOW communication protocol Be set to the same preset channel Be within a suitable reception range ESP-NOW provides direct device-to-device communication over the 2.4 GHz radio band, so a wireless router is not required. Receive-Only Operation This product is designed for situations where audio only needs to travel in one direction. It can be used as: A fixed listening point for a DSTIKE Walkie-Talkie A louder external receiver in a workshop A classroom ESP-NOW demonstration A one-way announcement receiver A development platform for wireless audio experiments A programmable notification speaker A companion receiver for maker projects It cannot be used for a two-way conversation by itself. For two-way communication, use two compatible DSTIKE ESP32 Walkie-Talkies. 10 Preset Channels The receiver supports the same 10 preset channels as the compatible DSTIKE Walkie-Talkie. A recessed channel-selection button is located behind the small access hole in the enclosure. Use a thin, non-conductive tool or suitable pin to press the button gently and change the channel. The speaker and transmitting device must be set to the same channel. If no audio is received, confirm the channel setting on both devices before checking other possible causes. Do not insert the tool too deeply or force the button, as this may damage the internal components. Status Indicator The onboard indicator shows the current operating state: Green: Powered on and standing by Blue: Receiving and playing audio Indicator behavior can be changed through custom firmware. Integrated 4Ω/3W Speaker The built-in 4Ω/3W speaker provides clearer and louder voice playback than a small buzzer. It is designed for speech, notifications and maker-project audio rather than full-range music reproduction. Perceived volume and audio quality depend on the transmitted signal, USB power quality, firmware settings and surrounding environment. USB-Powered Operation The receiver operates from a continuous 5V USB-A power source. It can be connected to a suitable: USB wall adapter Powered USB hub Computer USB port USB power bank Other stable 5V USB power source The USB connection supplies power during normal use. The factory firmware does not make the product a USB speaker or USB sound card, and it does not play computer audio through USB. The device does not contain a rechargeable battery. Reception Range Under open, low-interference and line-of-sight conditions, the maximum tested reception range can reach approximately 150 meters. Actual range depends on: Walls, floors and buildings Antenna orientation Nearby Wi-Fi networks Other 2.4 GHz devices Electrical interference Transmitting-device placement USB power quality Local environmental conditions The stated distance is an approximate test result under favorable conditions and is not guaranteed in every location. Indoor range will normally be shorter. Hardware Specifications Main controller: ESP32-WROOM-DA Wireless technology: ESP-NOW Wireless band: 2.4 GHz Operating mode: Receive-only Preset channels: 10 Tested range: Up to approximately 150 meters in favorable open conditions Speaker: 4Ω/3W Audio input: Compatible ESP-NOW voice transmission Power input: 5V through USB-A Internal battery: None Status indicator: Green and blue Channel control: Recessed push button Enclosure: 3D-printed plastic Firmware: Open source Schematic: Open source Assembly: Fully assembled Compatibility This receiver is designed for compatible DSTIKE ESP32 Walkie-Talkies using matching firmware and channel settings. It is not compatible with: Conventional analog walkie-talkies FRS radios GMRS radios PMR446 radios CB radios DMR radios Amateur radio transceivers Bluetooth audio transmitters Cellular push-to-talk services Standard Wi-Fi audio or casting systems It is also not a general-purpose Bluetooth speaker, internet radio or USB computer speaker under the factory firmware. Open-Source Development The schematic and firmware source code are available here: DSTIKE ESP32 Walkie-Talkie Speaker source files Developers can modify the project to explore: ESP-NOW data reception Wireless voice playback Custom channel systems RGB status behavior Audio processing Remote notification devices Sensor alarm receivers Custom one-way communication projects Uploading custom firmware will overwrite the factory program. Back up the original files and confirm the correct board and pin configuration before programming. Package Contents 1 × Fully assembled DSTIKE ESP32 Walkie-Talkie Speaker A transmitting walkie-talkie, USB power adapter and other accessories are not included. Important Notes This device can receive audio but cannot transmit. A compatible DSTIKE transmitter is required. The transmitter and receiver must use the same preset channel. Continuous 5V USB power is required. There is no internal battery. The product should not be used for emergency or safety-critical communication. Do not assume wireless transmissions are private or encrypted unless you have verified the installed firmware configuration. Reception range varies with the environment. The ESP32-WROOM-DA module has reached End of Life, so future availability of this exact hardware version may be limited. Because the enclosure is 3D printed, minor layer lines and small surface variations are normal. Safety and Handling Use a stable 5V USB power source. Keep the device away from water and high temperatures. Do not place exposed connectors against conductive objects. Disconnect USB power before opening or modifying the enclosure. Do not sharply bend or damage internal wiring. Stop using the device if the board, speaker or USB connector becomes unusually hot. Custom hardware and firmware modifications are performed at the user’s own risk. A Simple ESP-NOW Listening Point The DSTIKE ESP32 Walkie-Talkie Speaker provides a convenient fixed receiver for compatible DSTIKE voice devices. Plug it into USB power, select the matching channel and use it as a clear receive-only endpoint—or modify the open-source project for your own ESP32 wireless audio application.