Alcantara Steering Wheel Cover for Tesla Cybertruck (2024–On)

Alcantara Steering Wheel Cover · Cybertruck 2024–On New cabin style. Same original wheel. Refresh the wheel you already have with dark Alcantara texture and your choice of style. A visible cabin update to welcome you every time you get in, without replacing the steering wheel. Keep your original wheelHand-sewn Cybertruck fit Refresh, Don't ReplaceGive your cabin a new look while keeping your original steering wheel. Cybertruck-Specific FitShaped for the factory wheel and hand-sewn for a tailored finish. Everyday Alcantara TextureA finely textured surface on the wheel you reach for every day. 01 · Refresh, Don't Replace A cabin upgrade you see every day. Keep your original Cybertruck steering wheel and give it a different look with a fitted Alcantara cover. Dark texture and a choice of styles refresh this cabin focal point without replacing the wheel assembly. Choose the version that suits your interior. 02 · Cybertruck-Specific Fit Distinctive shape. Hand-stitched detail. Designed around the matching original steering wheel on 2024–on Tesla Cybertruck vehicles. The cover follows the upper edge, side grips and lower profile, while careful alignment and even stitching bring the sections together for a tailored finish. Compare your factory wheel with the product images before ordering. 03 · Everyday Alcantara Texture Texture for your everyday routine. From getting in for your morning commute to heading home, your steering wheel is part of every drive. A finely textured Alcantara surface adds a tactile detail to that familiar point of contact, paired with a dark, low-sheen finish. DIY stitch-on installation A tailored fit, stitched by you. Align the cover, work through the stitching and check the finished fit. This is a hand-sewn cover, not a slip-on accessory. Follow the instructions for your supplied kit, or choose a qualified trim installer. 01 Align Test-fit the cover and center the openings before securing anything. 02 Stitch Follow the supplied stitch pattern with even tension, one section at a time. 03 Check Inspect the fit and make sure the cover stays secure and controls remain clear. Installation Guide Clean and center. Clean the factory rim using a method approved for its surface and let it dry fully. Test-fit the cover and align all spoke openings and any center marker before securing it. Secure temporarily. If the kit instructions call for double-sided tape, apply it only after confirming alignment. Keep adhesive away from controls, seams and the airbag cover. Stitch evenly. Follow the supplied stitch pattern, working in short alternating sections. Keep tension even without pulling tightly enough to distort the cover. Tuck carefully. Only tuck edges where the kit instructions specify, using the recommended trim tool. Avoid scratching surfaces or obstructing buttons. Do not remove or modify the airbag assembly. Finish and inspect. Secure and trim the thread according to the instructions. Inspect the entire rim for loose areas, slipping, exposed thread or interference with controls. Check before driving. While safely parked, check that buttons and scroll wheels remain unobstructed and your hands have adequate clearance. If the cover slips or interferes with operation, do not drive until it is corrected by a qualified installer. Before you drive Keep buttons and controls unobstructed. Do not remove or modify the airbag assembly. If the cover slips or interferes with operation, do not drive until a qualified installer corrects it. If you are unsure about the patience, dexterity or trim experience required, choose a qualified automotive upholstery or trim installer. Care Keep the texture looking its best. Use a soft brush and gentle, light passes to remove loose surface dust. Avoid soaking the surface, aggressive scrubbing or unapproved solvents. Follow the material care instructions supplied with the cover. Fitment Compatible vehicles ✓Tesla Cybertruck (2024–on) Compare your original steering wheel with the product images before ordering. An aftermarket wheel or an existing wrap can change the fit. Not covered by this fitment list ×Tesla Model 3 ×Tesla Model 3 Highland ×Tesla Model Y ×Tesla Model Y Juniper ×Tesla Model Y Standard ×Tesla Model YL ×Tesla Model S ×Tesla Model X This is a vehicle-specific cover. For an unlisted steering wheel configuration, confirm fitment with TESERY before ordering. Down to the details Product Details ProductSteering wheel cover VehicleTesla Cybertruck Model years2024–on MaterialAlcantara ColorBlack Wheel applicationMatching original steering wheel Frequently Asked Questions Is this a complete steering wheel? No. This product is a cover for the existing steering wheel. A replacement wheel assembly, buttons and electronics are not described as part of this listing. What material is this cover? This cover is made with Alcantara in a black finish, with a finely textured, low-sheen appearance. Does it fit every Tesla? It is intended for the matching original steering wheel on 2024–on Cybertruck vehicles. Other Tesla models and modified steering wheels are not covered by this fitment. How is it installed? This is a fitted, sewn cover. Follow the instructions for the exact supplied set and use a qualified automotive trim installer if needed. Keep buttons and controls unobstructed; do not modify the airbag assembly. Does the photo confirm the center trim is included? The reference shows a coordinated Alcantara appearance across the wheel and center area. Confirm the supplied coverage with TESERY before ordering if you need the center section as well as the rim. Does this cover have a heating function? No. This steering wheel cover does not include a heating function or heating components. It is a non-heated, stitch-on cover for your existing wheel.