RockLock Bolt-On Selfie Stick Mount for Motorcycles

Bolt it on. Leave it on. RockLock replaces your passenger peg with two CNC aluminum clamps that hold your selfie stick tight against the bike. No clamps to crank down before every ride, no ball joints to creep loose over a few hundred miles. Set your angle once, torque the bolts, and it stays exactly where you put it. Bolted, not clamped Crab claw and strap mounts grip the outside of your frame. RockLock threads into the passenger peg mounting point itself, the same hardware that holds a passenger's weight. Two mounting points, two clamps, zero flex. Low profile The stick runs tight along the bodywork instead of standing off the bike on articulating arms. Less to catch on your leg, less to snag when filtering, and a cleaner look when the camera comes off. Fixed angle, set and forget There is nothing to adjust mid-ride because there is nothing that can move. If you shoot the same rear angle on every ride, this is the mount for you. If you like to reposition between shots, the Hyper-Stable Dual-Point stick with crab claw mounts is the better choice. Full CNC aluminum Machined from solid aluminum billet, black finish, stainless hardware. No plastic in the load path. Works with your existing stick, or ours Rubber inserts cover stick diameters from 0.75" (19mm) to 1.375" (34.92mm), so the mounts work with the Hyper-Stable stick and most other rigid selfie sticks and tubes. Already have a stick? Choose Mounts Only. Need one? Choose Mounts + Selfie Stick and get our 120cm Hyper-Stable extendable stick that's designed specifically for motorcycle riders. About the stick (Mounts + Selfie Stick) Extends from 46.8cm to 120cm (18.4" to 47.2") with a manual twist lock that engine vibration cannot back off. The 1/4" camera thread sits inside a rubber vibration pad that keeps your camera from wiggling loose on rough roads. Compatibility RockLock mounts through the 10mm hole where your passenger peg bolts on, on either side of the bike. The passenger peg is removed to install it. Peg bolt designs vary between manufacturers, so check that your bike has a removable passenger peg with bolted-through mounts before ordering. In the box Mounts Only 2 x RockLock CNC aluminum clamps Anti-slip rubber inserts in multiple sizes (0.75" to 1.375") Hex key Mounts + Selfie Stick Everything above Hyper-Stable extendable selfie stick, 46.8cm to 120cm Specs Clamp material: CNC machined aluminum, black finish Mounting hole: 10mm Stick diameter range: 0.75" to 1.375" (19mm to 34.92mm) Mount type: Dual bolt-on, passenger peg location Tools required: yes (hex key - included) Stick collapsed length: 46.8cm / 18.4" Stick extended length: 120cm / 47.2" Camera thread: 1/4"-20 Stick lock type: manual twist lock FAQ Do I lose my passenger peg? Yes, on the side you install it. The clamp bolts into the peg's mounting point. Swap the peg back in when you need it. Will it fit my bike? Most bikes with removable passenger pegs and a bolt-through peg mount will work. Bolt designs vary by manufacturer, so check yours before ordering. If you are unsure, send us a photo of your peg mount. Can I adjust the angle? The clamp position is fixed once bolted. You choose the angle on install by how you position the clamps and stick. For a mount you can reposition ride to ride, look at the Hyper-Stable Dual-Point. Which variant should I pick? If you already own the Hyper-Stable stick or another rigid stick between 0.75" and 1.375" in diameter, pick Mounts Only. If not, pick Mounts + Selfie Stick. Can I leave it on the bike? That is the point. Bolt it on and leave it. Remove the camera when you park.