SpeedyBee F405 V5 Stack - F405 FC + 55A 3-6S OX32 ESC - 30x30 - Deluxe

The SpeedyBee F405 V5 Stack - F405 FC + 55A 3-6S OX32 ESC - 30x30 - Deluxe features an upgraded F405 flight controller and OX32 ESC. The Deluxe edition includes a bunch of extras to simplify working with this stack. With the built-in Bluetooth chip, use Betaflight to tune in the field. With a built-in barometer and connectivity to all DJI Air Units, along with UART ports for maximum customizability, this stack was crafted with precision - your all-in-one choice for top performance. Check out all our 30x30 stacks & combos, and all our Speedy Bee products! Features Deluxe Edition comes with Soldering Practice Board, Power Expansion Board, USB Extension, and Smart Short-Circuit Protection Tool New clock sync function improves detection accuracy Easier soldering with added direct sockets for GPS and receiver Nickel-plated bus bars Double-sided heat-spreading Wireless tuning and upgrading Specifications F405 FC MCU: STM32F405 IMU (Gyro): ICM42688P USB Port Type: Type-C Barometer: SPA06-003 OSD Chip: AT7456E Bluetooth Tuning: Supported. Connect via SpeedyBee App for FC firmware flashing and parameter tuning Wireless FC Firmware Upgrade: Supported DJI Air Unit Connection: Supports 6-pin direct plug-in or solder connection Blackbox: Supported, built-in 16MB storage chip Input Voltage: 3-6S LiPo Battery 5V BEC Output: 9 groups (4x +5V pads, 1x BZ+ buzzer pad, and 4x 5V pads at corners for LEDs 9V BEC Output: 2 groups (1x 9V pad on front, 1x 9V pad on back). Supports PINIO remote on/off control MCU & Gyro Power: Independent LDO 3.3V Output: 1 group (1x 3.3V pad on front) 4.5V Output: 3 groups (3x 4.5V pads on front) Can power receiver & GPS when FC is powered via USB. Max current 1A. ESC Signal: M1-M4 pads and 10-pin connector on back Servo Signal: S5-S6 pads on the front ESC Telemetry Input: Supported (UART 5) Betaflight Camera Tuning Pad: Supported (CC pad on front) I2C: Supported (GPS connector + pads) UART UART1: Bluetooth UART2: front pads for receiver UART3: DJI VTX pads + 6-pin SH1.0 UART4: GPS pads + front 6-pin SH1.0 UART5: TLM UART6: receiver pads + rear 4-pin SH1.0 ST LED Pads: Supported, on front G/5V/LED Meteor LED Strip Pads: Supported Buzzer Pads: Supported BOOT Button: A: Hold BOOT while powering on to force DFU mode for flashing. B: When powered and in standby, short=press cycles LED display modes; long press switches SB-LED/ST-LED. RSSI Pads: Supported Smart Port: Not Supported Supported FC Firmware: Betaflight Firmware Target Name: SPEEDYBEEF405V5 Factory Firmware Version: Betaflight 4.5.2 Configurator Version: Betaflight 10.10.0 Mounting Holes: 30.5 x 30.5 mm (⌀4mm) side opening Dimensions: 39mm x 39mm x 4.9mm (LxWxH) Weight: 8.1g 55A 3-6S OX32 ESC - 30x30 Default Firmware: OX32 Continuous Current: 55A (per channel) / 220A (4-in-1) Maximum Current: 70A (per channel) / 280 (4-in-1) TVS Protective Diode: Yes (built-in) External Capacitor: 1000µF Solid Capacitor ESC/Motor Protocol: DSHOT300/600 Input Voltage: 3-6S Lipo Power Output: VBAT Current Sensor: Supported ESC Telemetry: Supported Mounting Holes: 30.5 x 30.5 mm (⌀4mm) side opening Dimensions: 40.9mm x 44.9mm x 8mm (LxWxH) Links ESC Webpage Includes 1x SpeedyBee F405 FC 1x SpeedyBee 55A 3-6S OX32 ESC 1x Soldering Practice Board 1x Short-Circuit Protection Tool 1x Active Buzzer 4x Power Expansion Boards 1x Buzzer Red & Black Wires 100mm 1x Type-C Extension Module 1x 1000uf/35V Capacitor 1x XT60 120mm Connector 2x Capacitor Heat Shrink Tube 4x M3 Stack Mounting Bolts 30mm 5x M3 Hex Nylon Nuts 5x M3 Black Silicon Washers 5x M2 Anti Vibration Silicone Grommets 5x M3 Anti Vibration Silicone Grommets 1x 25mm 10-Pin SH1.0 1x 75mm 10-Pin SH1.0 1x 80mm 6-Pin SH1.0 1x 120mm 6-Pin SH1.0 1x 120mm 6-Pin SH1.0 to 4-Pin SH1.0 1x 100mm 4-Pin SH1.0 1x Quickstart Guide