HK Army Turbine Pro Air Tank Regulator Long Body

HK Army Turbine Pro Air Tank Regulator Long Body – Extra Length, Same Elite Performance This is the long body version of HK Army's top performing regulator, the Turbine Pro. It gives you everything players love about the standard Turbine Pro (fully adjustable output pressure, a rotating cap you can lock into any position, and air consistency you can count on shot after shot) with extra length built in for players who need more room between their tank and their marker. Every unit is 100% tested for leaks and pressure before it ships, so you know it's ready to perform right out of the box. 360° Rotating Cap for Perfect Gauge and Fill Valve Placement The Turbine Pro's cap rotates a full 360 degrees, so you can set your gauge and fill valve at your preferred position. Once you find that spot, flat alignment zones and set screw locks hold it in place. Dual o-rings back up that seal where the regulator threads into your ASA, so you get double the leak protection right at the connection point. Fully Adjustable Output Pressure: 350 to 650 PSI Switching pressure settings takes seconds. Just swap in the pressure shim that matches your target PSI (350, 450, 550, or 650) and you're set. Each shim is laser etched for easy identification. Out of the box, this regulator arrives preset to 450 PSI, which lines up well with most Planet Eclipse, DLX Luxe, Dye, Empire, and Shocker markers. Built to Deliver Steady Air, Game After Game Air Flow Stabilizer: A brass insert inside the regulator softens that initial rush of air, keeping pressure output smooth and even. CNC Milled Body: The milled exterior isn't just there to look sharp. It gives you a better grip when you need to turn or adjust your tank mid game. Low-Profile Burst Discs: These sit closer to the body of the regulator so they stay out of your wrist's way. A small socket wrench comes included for whenever you need to swap one out. Full Color Micro Gauge: Check your remaining air at a glance with a gauge that's easy to read. Upgraded Pin Valve: A larger pin valve improves airflow, and a stiffer spring and o-ring combo keeps your rebound pressure stable over the long haul. Spring Loaded Fill Valve: This keeps dirt and debris out whether you're transporting your tank or it's sitting empty. A rubber cover adds one more layer of protection against debris. Pro Grade Testing on Every Single Unit Before a Turbine Pro Regulator ever leaves the factory, it goes through a thorough quality check: Incoming Inspection: Each part gets checked against exact dimensions before assembly even starts. Ultrasonic Cleaning: This step clears out machining oils and leftover debris for a clean, finished look. Expert Assembly: Techs build every regulator to HK Army's own performance standards. 100% Leak and Pressure Testing: Nothing ships until it's confirmed leak free and holding pressure within spec. Everything You Need to Keep It Running Your Turbine Pro Regulator arrives with a full rebuild kit in the box: extra o-rings, three pressure shims, a piston o-ring, a pin valve o-ring, a socket wrench, an allen wrench, and set screws. Long Body Sizing This listing is for the long body version: Complete Regulator: 3.85 in (98mm) Exposed When Screwed On Tank: 2.85 in (72mm) Looking for something more compact? The standard body Turbine Pro Regulator is also available as a separate listing here. Frequently Asked Questions How much longer is the long body Turbine Pro compared to the standard version? The long body version measures 3.85 in (98mm) complete with 2.85 in (72mm) exposed once it's screwed onto your tank, about half an inch longer than the standard body in both measurements. Can I still rotate the gauge and fill valve on the long body model? Yes. The long body regulator uses the same 360° rotating cap with set screw locks, so you can position and lock your gauge and fill valve exactly where you want them. What PSI settings does the long body Turbine Pro support? It adjusts across the same range as the standard version: 350, 450, 550, and 650 PSI using the included pressure shims. It ships preset to 450 PSI. Why would I choose the long body over the standard body regulator? Some players prefer the extra length for how it fits with certain tanks, grips, or personal setups. Performance is identical between the two, so it comes down to fit and feel. What's included with the long body Turbine Pro Regulator? Every unit ships with a full rebuild kit: spare o-rings, three pressure shims, a piston o-ring, a pin valve o-ring, a socket wrench, an allen wrench, and set screws.