Raypak Natural Gas Pool Heater 150K BTU 156A 014784

The Raypak 156A (014784, P-R156A-EN-C) is a 150,000 BTU natural gas pool heater for above-ground and in-ground pools at elevations from sea level to 4,999 feet. It uses Raypak's AFT digital controls, a copper fin-tube heat exchanger, polymer headers, and a PolyTuf powder-coated galvanized steel cabinet. This is the natural gas version rated for 0–4,999 ft. Gas heater sizing reflects recovery speed — how fast the heater raises pool temperature from cold — not steady-state energy demand. Cooler climates, shaded pools, or pools without a solar cover should size conservatively. Raypak 156A 014784 - Pool Size by Climate Raypak 156A 014784 - Pool Size Estimate by Climate Climate Recommended Pool Size Warm climate (moderate heat loss) Up to 10,000 gallons Cooler climate or high heat-loss pool 6,000–8,000 gallons These figures reflect heat-up speed from a cold pool, not steady-state maintenance load. Above-ground and in-ground pools both supported. A solar cover significantly reduces heat loss and fuel use. Raypak 156A 014784 - Key Features The 156A uses Raypak's AFT digital control board with a microprocessor thermostat, LCD display, plain-text self-diagnostics, flame strength indicator, and run-time and cycle meter. Ignition is intermittent spark-to-pilot: the pilot fires only when the thermostat calls for heat, conserving gas between cycles. The copper integral-fin-tube heat exchanger uses single-piece extruded copper construction with stainless steel tube sheets. Polymer (Capron resin) headers prevent rust staining on pool surfaces. The Unitherm Governor keeps inlet water above 105°F to prevent condensation and scale. An automatic internal bypass valve manages flow across varying pump speeds. The ProTek Shield module provides replaceable sacrificial corrosion protection at the exchanger inlet. The low-profile pagoda-top cabinet drafts naturally without a fan. The unit ships factory test-fired with a 3-foot, 3-prong 120V power cord. Raypak 156A 014784 - Full Specifications Raypak 156A Natural Gas Pool Heater 014784 — Complete Technical Specifications (P-R156A-EN-C) Specification Value Model Number P-R156A-EN-C Part / SKU 014784 BTU Input Rate 150,000 BTU/hr (43.93 kW) Thermal Efficiency 82% Fuel Type Natural Gas Elevation Rating 0 to 4,999 ft above sea level Min. Gas Supply Pressure 3.5" W.C. at heater inlet Gas Connection 1/2" NPT Ignition Electronic spark-to-pilot, intermittent with flame supervision Controls Raypak AFT Digital — LCD display, self-diagnostics, flame strength indicator, run-time and cycle meter Voltage 120 VAC (field-convertible to 240 VAC), single-phase Breaker 15 amp dedicated circuit Electrical Connection 3-ft., 3-prong 120V power cord (field-convertible to 240V) Heat Exchanger Integral copper fin-tube with stainless steel tube sheets Header Material Polymer (Capron resin) — rust-stain free Burner Stainless steel hybrid, self-adjusting ProTek Shield Included (replaceable sacrificial corrosion protection) Max Water Flow 70 GPM Plumbing Connection 2" NPT flanges (included) Compatible Pool Types Above-ground and in-ground; chlorinated and salt water Pool Size Estimate Up to ~10,000 gal (warm climate); 6,000–8,000 gal (cooler climates) Venting Category I atmospheric; outdoor stackless top included; indoor drafthood required separately Remote Control 2-wire or 3-wire; compatible with most major pool automation systems Water Chemistry Free chlorine max 5 ppm; pH 7.2–7.8; salt max 4,500 ppm Shipping Weight 100 lbs (45.4 kg) Low NOx Not Low NOx rated — cannot be sold in SCAQMD counties (SoCal) or Utah Certifications ANSI Z21.56 / CSA 4.7 Raypak 156A 014784 - Warranty Raypak 156A 014784 Warranty Terms — Professional Installation Required Coverage Term Conditions Parts — Standard Residential 2 years Registered with installation receipt at raypak.com Parts — New Construction (Builder) 3 years Registered within 90 days of installation with receipt Parts — Without Registration 1 year No registration or missing receipt Labor Not covered Residential labor is owner's responsibility Installation Requirement Required Must be installed by a licensed contractor per all local codes Exclusions: water chemistry damage, freeze damage, and sprinkler/water contact with cabinet. Register at raypak.com immediately after installation. Raypak 156A 014784 - Installation Documents Raypak 156A Pool Heater — Installation and Operation Manual (P/N 241519) Raypak 156A Pool Heater — Limited Warranty (100-10000378) Raypak 156A Pool Heater — Product Brochure (6100.30) Frequently Asked Questions - Raypak 156A Natural Gas Pool Heater 014784 What pool size is the Raypak 156A 014784 designed for? In warm climates, up to approximately 10,000 gallons. In cooler climates or pools with high evaporation, shade, or wind exposure, size down to 6,000 to 8,000 gallons for comfortable recovery times. Compatible with both above-ground and in-ground pools and spas. What are the electrical requirements? The 014784 ships factory-wired for 120 VAC with a 3-foot, 3-prong cord on a dedicated 15-amp circuit. The internal transformer can be field-rewired to 240V without additional parts. All electrical work must be performed by a licensed electrician per local code. Is this a heat-only model? Yes. The 156A cannot cool pool water. Gas heaters excel at fast, on-demand heating regardless of ambient air temperature. If cooling is also needed, a heat pump with an integrated cooling mode is the appropriate addition. How does the natural gas 014784 compare to the propane 014786? Both deliver 150,000 BTU/hr at 82% efficiency with identical AFT controls, copper heat exchanger, and warranty terms. The natural gas 014784 is rated for 0 to 4,999 ft; the propane 014786 is rated for 0 to 1,999 ft only. Natural gas connects directly to a gas line; propane requires a stationary tank, two-stage regulator, and licensed gas contractor. Choose based on which fuel is available at your site. How does the 156A compare to the R206A (009216)? The 156A produces 150,000 BTU/hr and suits pools up to 10,000 gallons. The R206A (009216) produces 199,500 BTU/hr — roughly 33% more output — and suits pools up to 20,000 to 25,000 gallons. They are different cabinet platforms. If your pool is above 10,000 gallons, the R206A is the right step up. What are the warranty terms? Professional installation by a licensed contractor is required. Standard residential with registration and receipt: 2 years parts. New construction registered within 90 days with receipt: 3 years parts. Without registration: 1 year. Labor is not covered under residential warranty. Register at raypak.com immediately after installation.