MCS RR3 Triple Adjustable Monotube Dampers (NC MX5 Miata + RX8)

All MCS damper kits are built to order so expect an estimated 2-6 week build time after you order. If you chose to order online, you will be billed immediately. If you would like to call in the order (we prefer that) we process a deposit for the shocks up front, with the rest billed when they are complete. Introduction Vorshlag Motorsports is an authorized Motion Control Suspension dealer. The MCS RR3 external triple adjustable damper is the Motorsports solution for top level Time Trial competitors, Club Racers, and Autocrossers - even Pro road race teams. This damper set features a full 18 clicks Rebound control, 10 clicks of low speed Compression control, and 18 clicks of high speed Compression control - over a wide range and valved unique to each vehicle model's specific requirements. Dampers are more than just a number of adjustments and click count though – the shape of the resulting curves is specifically engineered to give your car the most grip through the range of surface conditions and dynamic inputs your vehicle experiences in a competition environment. High Speed Compression damping (above left) is easily manipulated on the 3W damper. With 18 clicks of adjustment, the user can control high speed shaft movements (4 inches of velocity and beyond) to make better use of their mechanical contact patch, resulting in faster lap times. Low Speed Compression damping (above right) has 10 clicks of adjustment, allowing the user can easily manipulate the pitch and roll of the vehicle in low speed shaft movements (0-4 inches in velocity). With 18 clicks of rebound adjustment (above middle), the user can easily introduce more spring control or change the balance of the car. With the Schrader valves fitted on the ends of the RR2 or RR3 reservoirs, the ability to increase or decrease the nitrogen pressure in your damper is another adjustment. This allows the user to increase or decrease the overall support to the vehicle. Reservoir pressure can be adjusted between 100 – 275 PSI to help support the platform in fast cornering that generates large loads or to allow more weight transfer to generate more traction in low grip scenarios. All the MCS dampers are built in the USA. They are fully rebuildable, serviceable and can be custom valved and upgraded any time here in the USA. Key Features Adjustment range of 18 different settings for rebound control (at knob on top of shock/strut) Adjustment range of 10 different settings for low speed compression control (at knob on remote reservoirs) Adjustment range of 18 different settings for high speed compression control (at knob on remote reservoirs) Monotube design front and rear Nitrogen pressure is adjustable if required Includes standard spring hardware (springs and top mounts are available as options) Parts Included: 2 Front MCS Remote Triple Adjustable (18 adj, Rebound, 10 & 18 adj. Compression) Monotube Shocks 2 Rear MCS Remote Triple Adjustable (18 adj, Rebound, 10 & 18 adj. Compression) Monotube Shocks 2 Rear spring adapters MCS Front Spring Perches for coilover springs and your OEM upper strut mounts Unique to Vorshlag: + We include a 1.5mm Allen wrench tool, which is used to tighten the rebound knobs onto the adjustment shaft. + Also included free of charge is a pair of Vorshlag 68-75mm Spanner Wrenches for MCS front coilover strut spring perches. These are needed to loosen/tighen the 2-piece perches on each strut. + MCS kits ordered from Vorshlag are shipped to our facility first. This way we can test fit any optional parts (springs, camber plates, etc) to the as-built struts and shocks, and give everything a final Quality Check. Almost all other MCS dealers drop-ship these kits direct from MCS to the customer. Included in all MCS kits with are these Spanner Wrenches, which Vorshlag builds for MCS perches Most MCS dealers just "sell shocks" and leave it up to the end user to figure out all of the pieces necessary to make them fit. Vorshlag designs, tests, manufactures, and offers all of the optional but necessary parts needed to install this MCS kit to the vehicle. This usually includes a spherical front top mount/camber plate, rear shock mounts, springs and often remote spring ride height adjusters. See below for more details. FRONT & REAR SPHERICAL TOP MOUNTS: Vorshlag makes spherical top mounts for the front (shown in red above) and for the rear (tall silver aluminum bits below. These are made to remove the rubber bushings for the top of all four shocks, and are highly recommended for racers buying MCS dampers. The rear top mounts made by Vorshlag are unique to the industry, and are made by machining new OEM rear upper top mounts to accept our massive 19mm ID spherical bearing holder. These include Delrin spring adapters to fit 2.5" ID rear coilover springs at the top end. These can work on the RX8 also, just not with the R2 style rear shock tower brace. SPRING PACKAGE : While MCS provides you with the dampers only, Vorshlag offers the unique option for racers to pick their own front and rear spring rates. These options will include new Hyperco or Eibach springs from our recommended packages. The spring options listed include our GT package for daily driven cars, the GTS package for street cars that are also used in autocross and/or track events and the GTR package for race cars that predominantly see track use. If you would like to order custom rates not listed here, please give us a call. This can be arranged for typically no extra cost. 2 Front 2.25" Coilover Springs 2 Rear 2.5" Coilover Springs Vorshlag's GT Spring Package: 550# Front / 350# Rear Vorshlag's GTS Spring Package: 700# Front / 475# Rear Vorshlag's GTR Spring Package 900# Front / 600# Rear If you would like to order custom rates not listed here, please give us a call. There is no additional charge for different spring rates. SIGNATURE DELIVERY : Orders over $2400 require signature delivery. Please plan on that when ordering. 2025/10