0AM927769D TCU DSG7 DQ200 Used

0AM927769D TCU DSG 7 DQ200 Used Part Number: 0AM927769D Original used transmission control unit for DSG 7-speed DQ200 mechatronics systems in selected VW Group vehicles Transmission Type DSG 7 DQ200 Component Mechatronics TCU Condition Used Fully Functional Manufacturer Temic Application VW Audi Skoda Seat Warranty 12 Months Tested & Ready for Further Programming or Cloning This original 0AM927769D control unit is intended for DSG 7-speed DQ200 mechatronics systems. It is a used tested component designed as a replacement for defective transmission control electronics in compatible VAG vehicles. OEM Part Numbers Main OEM Number: 0AM927769D Related Mechatronics / Hydraulic References: 0AM325025D • 0AM325065AB Related Transmission References: 0AM325025M • 0AM325025K Always Verify the Exact Part Number Before ordering, compare the OEM number on your original control unit with 0AM927769D. For many vehicles, correct operation also requires cloning, software transfer or loading the proper program and VIN-specific data. Technical Specifications Transmission Type: 7-Speed DSG DQ200 Component Type: Transmission Control Unit (TCU) System: DQ200 Mechatronics Manufacturer: Temic OEM Number: 0AM927769D Condition: Used - Tested Fully Functional Vehicle Group: Volkswagen Audi Skoda Seat Clutch Type: Dry Clutch DSG System Torque Range: For DQ200 applications up to 250 Nm Installation Note: Programming / cloning / adaptation may be required after installation Warranty Period: 12 Months Product Description This original used 0AM927769D unit is an electronic transmission control module for the DSG 7-speed DQ200 mechatronics assembly. The control unit processes transmission data, controls gearshift strategy, communicates with the hydraulic mechatronics system and helps manage clutch and gear engagement functions. What This TCU Does Controls electronic functions of the DQ200 mechatronics system Processes sensor inputs related to gearbox operation Supports shift management and transmission response Works together with the hydraulic mechatronics section for clutch and gear control Serves as a replacement for damaged or non-communicating original TCU units Programming Information In many cases, a replacement 0AM927769D unit must be cloned from the original module or loaded with the correct software and VIN-related data before use. Professional installation with suitable diagnostic equipment is strongly recommended. Vehicle Compatibility This control unit is used in selected Volkswagen Group vehicles equipped with 7-speed DSG DQ200 transmission and dry clutch system. Always verify both the exact OEM number and transmission type before purchase. Suitable for Selected Models Such As Audi A1 / S1 (2010 - 2014) Audi A3 (2008 - 2014) Audi Q3 (2011 - 2014) VW Golf (2008 - 2013) VW Beetle (2008 - 2013) VW Jetta (2008 - 2013) VW Caddy (2008 - 2014) VW Passat (2008 - 2014) VW Passat CC (2008 - 2014) VW Polo (2008 - 2014) VW Touran (2008 - 2014) Škoda Fabia (2008 - 2014) Škoda Octavia (2008 - 2013) Škoda Rapid (2012 - 2014) Škoda Yeti (2008 - 2014) Škoda Superb (2008 - 2014) SEAT Altea XL (2008 - 2013) SEAT Ibiza (2008 - 2014) SEAT Leon (2008 - 2013) SEAT Toledo (2008 - 2013) Compatibility Check Recommended DQ200 applications can differ according to software version, mechatronics configuration and vehicle production details. If you are not sure, send us your VIN number and the part number from your original module for verification before ordering. Common Fault Codes & Symptoms A failing DQ200 mechatronics control unit can cause shifting problems, loss of drive, warning messages or transmission emergency operation. Common diagnostic trouble codes and related complaints may include: P17BF Fault related to pressure control or internal mechatronics issues P1895 Pressure sensor / control-related malfunction P0841 Transmission fluid pressure sensor range / performance issue P1727 Clutch slipping or transmission operating fault P2711 Unexpected mechanical gear disengagement or shift monitoring problem P178B Vehicle remains stationary / transmission does not engage properly P174D Gear actuator or mechatronics control-related issue P0562 Supply voltage too low P0928 Gear actuator circuit range / performance fault P073A Gear engagement problem Vehicle will not move or only selects certain gears Engine may not start because transmission status is not recognized correctly Gearbox warning light or transmission fault message on dashboard Loss of odd or even gear operation Jerking, delayed engagement or limp mode operation Diagnostic Note Fault codes alone do not always prove that the TCU is defective, because wiring, hydraulics, sensors or internal mechatronics faults can produce similar symptoms. Proper diagnosis before replacement is always recommended. Installation & Service Notes Recommended Steps Check the exact OEM number on the original control unit Confirm that the gearbox is a DSG 7 DQ200 version Inspect the mechatronics assembly for related hydraulic or electrical damage Clone the original unit or load the correct software where required Install the module carefully using professional workshop procedures Perform diagnostic checks, fault code clearing and adaptation after installation Verify gearbox operation during test drive after repair Important Installation Note This product is an electronic transmission component. Incorrect programming, mismatched software or improper installation can prevent the gearbox from operating correctly. Installation by a DSG specialist is strongly recommended. Why TCU Replacement Matters 1. Restores Communication A healthy control unit is essential for communication between the gearbox mechatronics, sensors and vehicle systems. 2. Supports Correct Shifting The TCU manages transmission logic and helps maintain proper gear selection and clutch operation. 3. Prevents Repeat Faults When a defective module is correctly replaced and programmed, recurring control-related transmission faults can be eliminated. 4. Improves Reliability A tested replacement unit helps restore dependable DSG operation when the original electronics have failed. Quality Assurance & Warranty 12-Month Warranty: This used original transmission control unit is tested before dispatch and supplied with a 12-month functionality warranty under normal operating conditions. Final operation always depends on correct installation, matching software and overall gearbox condition. Quality Control Includes: Verification that the unit is an original OEM-type component Functional testing before shipping Visual inspection of connector and housing condition Basic identification and part number check Warranty Coverage Includes: Functional defects of the supplied control unit itself Manufacturing-related internal electronic defects Verified non-functionality of the delivered module under normal intended use Warranty Exclusions: Damage caused by incorrect installation Software mismatch, failed programming or cloning errors Hydraulic or mechanical gearbox faults unrelated to the TCU Electrical damage caused by wiring or voltage problems in the vehicle Physical damage, water ingress or tampering Questions or Need Help? We can help verify part number compatibility and advise whether this 0AM927769D control unit is suitable for your gearbox. Contact Important Purchase Information Please compare the OEM number on your original unit before purchase This is a used electronic transmission control unit Programming, cloning or adaptation may be required Professional installation is recommended Photos are for illustrative purposes only Worldwide shipping is available If your country is not listed at checkout, contact us for manual order processing Please check carefully whether this product matches your vehicle and gearbox version before ordering