Victron Lynx Shunt VE.Can 1000A Battery Monitor (M10)

Victron Lynx Shunt VE.Can 1000A Battery Monitor (M10) Combines a 1000A battery shunt, positive and negative DC busbars, and a location for the main system fuse in one Lynx module. Shows battery state of charge, current, power, time remaining, temperature and alarm status through a compatible Victron GX device. M10 busbars for integration into modular Victron Lynx DC distribution systems. Victron Lynx Shunt VE.Can battery monitoring and DC distribution The Victron Lynx Shunt VE.Can is a 1000A DC busbar module with an integrated battery monitor and holder for the main system fuse. It is designed for larger 12V, 24V and 48V Victron installations where a central, structured approach to DC distribution, fusing and battery monitoring is required. Connect it to a compatible GX device, such as Cerbo GX, by VE.Can to view system data locally and remotely through the Victron VRM portal. The Lynx Shunt VE.Can is not a BMS: it monitors the battery bank and its main fuse, while the connected GX device provides configuration and data display. Key features 1000A continuous DC rating: Suitable for high-current inverter, charger and battery-bank systems within its 12V, 24V or 48V operating range. Integrated battery monitoring: Measures battery voltage, current, power, state of charge, amp-hours consumed and estimated time remaining. Main-fuse provision: Includes a position for the system main fuse; the fuse is purchased separately and must be selected for the installation. GX and VRM integration: VE.Can communication sends operational data, alarms and history to a connected GX device and, where configured, the VRM portal. Programmable alarm relay: Can respond to battery state of charge, voltage, temperature or a blown main fuse through GX-device configuration. Where to use Use the Victron Lynx Shunt VE.Can in high-current solar, off-grid, marine, mobile, backup-power and commercial DC systems built around the Victron Lynx Distribution System. Typical configurations combine it with Lynx Power In, Lynx Distributor and a Cerbo GX or other compatible GX device. Install the battery bank on the Lynx system’s battery side and connect all DC loads and charging sources on the system side so the shunt can calculate battery state of charge correctly. This is a specialist DC-distribution product; use a qualified installer or one of Energian’s trusted partners to design fusing, cable sizes, busbar connections and commissioning. Technical specifications Product Victron Lynx Shunt VE.Can Versions M10 busbar versions Product type DC busbars with integrated battery monitor and main-fuse holder Supply voltage range 9–70V DC Supported system voltages 12V, 24V or 48V Reverse-polarity protection No Continuous current rating 1000A DC Equivalent nominal power at 1000A 12kW at 12V; 24kW at 24V; 48kW at 48V Power consumption 60mA at 12V; 33mA at 24V; 20mA at 48V Potential-free alarm contact 3A at 30V DC or 250V AC Battery-monitor information Battery voltage, current, power, state of charge, consumed amp-hours, time remaining, temperature, alarms and history Communication VE.Can, RJ45; two VE.Can RJ45 terminators supplied GX-device requirement Compatible GX device required for monitoring, setup and relay configuration NMEA 2000 support Supported through VE.Can with a VE.Can to NMEA 2000 micro-C male cable, sold separately Temperature sensor connection Screw terminal; temperature sensor included Relay connection Screw terminal Fuse provision, M8 version Designed for a CNN fuse; fuse not included Fuse provision, M10 version Accepts CNN, ANL or Mega fuses; fuse not included M10 fuse-dummy busbar Included; allows the main fuse to be located outside the unit when required Busbar material Tinned copper Busbar dimensions, H × W 8 × 30mm Enclosure material ABS Enclosure dimensions, H × W × D 190 × 180 × 80mm Unit weight 1.4kg Operating temperature range -40°C to +60°C Storage temperature range -40°C to +60°C Humidity Maximum 95%, non-condensing Protection class IP22 Documents available for download Victron Lynx Shunt VE.Can Datasheet Victron Lynx Shunt VE.Can M10 Installation and User Manual Shipping Available for shipping to the UK, Ireland, Africa, the Caribbean and worldwide. If the shipping rate is not shown at checkout, contact us on +44 2080640335 or info@energian.co.uk for a quote. UK expert support UK expert support is available for Victron Lynx system design, battery monitoring, fuse selection and DC distribution. Contact us with questions or support requests by phone, email or live chat, or visit our office for an in-person consultation.