Proline X Micro Series Dual 10" Sealed Enclosure - Fits ResoNix GUS 10

Micro Series | Dual GUS-10 | Enclosure Only Dual GUS-10. 1.26 cu ft Total. 0.60 cu ft Acoustic Per Driver — ResoNix's Optimum. Two ResoNix GUS-10 drivers. Two acoustically isolated sealed chambers. Each chamber holds 0.63 cubic feet gross — which after the GUS-10's 0.031 cubic foot driver displacement delivers 0.599 cubic feet of net acoustic airspace per driver. ResoNix's published 0.707 Qtc target is 0.60 cubic feet. The M10D-S GUS hits that target precisely in 8.25 inches of total depth. 1,000 watts RMS combined. 1.26 Cu Ft Net Total 0.60 Cu Ft Acoustic Per Driver 8.25" Total Depth 1,000W Combined RMS Rating Enclosure only. ResoNix GUS-10 subwoofers are not included and must be purchased separately from ResoNix Sound Solutions. Both the D2 and D4 variants fit this enclosure. Select the impedance variant that matches your amplifier's stable load before ordering. 0.63 cu ft Per Chamber — 0.60 cu ft Acoustic After Displacement ResoNix publishes a 0.707 Qtc target of 0.60 cubic feet of net acoustic airspace for the GUS-10. The GUS-10 has a driver displacement of 0.031 cubic feet. Each chamber in the M10D-S GUS is built to 0.63 cubic feet gross — after the driver is installed, each GUS-10 sees 0.599 cubic feet of net acoustic airspace, hitting ResoNix's 0.60 cubic foot target to within rounding. The 1.26 cu ft total listed is the gross volume across both chambers. The acoustic figure that matters for each driver is 0.60 cu ft per chamber. This is a cleaner acoustic alignment than the single M10-S GUS, which runs 0.603 cu ft net and sits fractionally below the 0.60 target. The dual build, with its larger overall enclosure volume to work with, hits the per-chamber target more precisely. Both drivers load into identical acoustic conditions. Two GUS-10 Drivers — Double the Displacement, Same Alignment The GUS-10's case as the front sub platform rests on three things: 4.12 inches of mounting depth, Klippel-verified 18.37mm one-way Xmax, and a flat 0.707 Qtc sealed alignment that extends well below 20 Hz. A single GUS-10 delivers all of that from one driver. Two GUS-10 drivers in isolated 0.60 cubic foot chambers double the cone displacement — the variable that determines how much air is moved at any given frequency — and raise the combined power handling to 1,000 watts RMS. The acoustic character does not change between the single and dual builds. Both GUS-10 drivers have Qts of 0.35 and Fs of 16.91 Hz. Each loads into a 0.707 Qtc sealed alignment. The response is flat and extended anechorically but lean in the upper bass register without active shelf EQ. A Goldhorn DSP or equivalent processor remains the correct companion for this system — the dual build makes the response louder and deeper, not warmer or more forgiving without EQ. 1,000W Combined — Double-Layer Baffle, Dado Joinery, Dowel Reinforced The front baffle is a double-layer stack-fab build — two CNC-cut Langboard Elite MDF panels bonded to 1.5 inches total. At 1,000 watts RMS combined across two high-excursion 10" drivers, baffle resonance is a structural concern, not a theoretical one. The stack-fab assembly is reinforced with dowels throughout the build, adding mechanical alignment and shear resistance at every panel joint beyond what dado joinery and adhesive alone provide. The chamber divider is CNC-cut and dado-jointed to the same standard as every exterior panel. It is a structural element — both chambers maintain their acoustic isolation and geometric integrity under sustained 1,000-watt operation. Impedance Wiring — Know Before You Order 2Ω Two GUS-10 D2 — each wired series (4Ω per driver), then both in parallel → 2Ω final. Recommended for most builds. Broadest amplifier compatibility. Target a monoblock delivering 800–1,000W RMS at 2Ω. 4Ω Two GUS-10 D4 — each wired parallel (2Ω per driver), then both in series → 4Ω final. Safest electrical configuration. Widest amplifier selection. Requires a strong 4Ω monoblock to reach the 1,000W combined ceiling. 8Ω Two GUS-10 D4 — each wired series (8Ω per driver), then both in parallel → 4Ω final. Note: two D4s in series then parallel also yields 4Ω. For a true 8Ω load, wire two D4s in series only (one driver). Not a typical dual-driver configuration. Volume 0.60 cu ft Acoustic Per Driver — ResoNix's 0.707 Qtc Target Each chamber is built to 0.63 cu ft gross. After the GUS-10's 0.031 cu ft displacement, each driver sees 0.599 cu ft net acoustic airspace — essentially exactly ResoNix's published 0.60 cu ft optimum. Both chambers are identical. Both drivers load correctly. Output 1,000W RMS Combined — Dual Klippel-Verified Xmax Two GUS-10 drivers at 500W RMS each with 18.37mm Klippel-verified Xmax per driver. Combined cone displacement doubles the output potential of the single GUS-10 build — particularly below 30 Hz where cone area and linear excursion are the dominant output variables. Chambers Dual Chamber — CNC Divider, Dado Jointed, Independently Sealed A CNC-cut, dado-jointed chamber divider separates both driver volumes completely. Neither GUS-10 shares airspace with the other. Each driver loads independently into its own 0.63 cu ft sealed chamber — correct acoustic alignment on both sides. Baffle 1.5" Double-Layer — Dowel Reinforced Stack Fab Two bonded layers of Langboard Elite 3/4" MDF at 1.5 inches total, further reinforced with dowels throughout the assembly. At 1,000 watts RMS combined, double-layer stack-fab construction eliminates baffle resonance at the structural level. Wiring Single Proline X Terminal Cup — Pre-Wired to Both Drivers One Proline X ABS/carbon fiber terminal cup with stainless hardware and copper ring terminals serves the entire enclosure. Pre-wired internally with 12-gauge OFC to both driver positions. One amplifier run feeds both drivers. Mounting 8/32 Threaded Inserts — Machine Screws for Both Drivers Both baffle positions are fitted with 8/32 threaded inserts. Stainless machine screws are included for both GUS-10 drivers. Each driver mounts to steel — consistent clamping force, no stripping risk, clean reinstallation at any service interval. DSP Active EQ Required — Identical Character to the Single GUS-10 Both GUS-10 drivers have Qts of 0.35, Fs of 16.91 Hz. The 0.707 Qtc alignment in each chamber produces flat anechoic response requiring active shelf EQ in-cabin. A Goldhorn DSP is the correct companion. Two drivers make the response louder — they do not change its character. Clearance 23mm Minimum Front Clearance — Both Drivers ResoNix specifies 23mm minimum clearance between the GUS-10's surround and any surface in front of the driver. Confirm this at both driver positions against seat cushion, cargo cover, or any other nearby surface before finalizing the install. Configuration Front-Firing or Downfiring — Feet Included Rubber feet for downfiring installation are included. The GUS-10's vented rear cone assembly allows the pole vent to be fully obstructed without acoustic penalty — downfire is viable in tight enclosures. Choose the orientation that makes the install cleanest and most serviceable. Reinforcement Dowel-Reinforced Stack Fab — Three Mechanical Systems at Every Joint Dowels throughout the stack-fab assembly resist shear forces at panel joints independent of adhesive condition. Dado joinery + adhesive + dowels — all three systems locking every joint against sustained load across the life of the installation. Ready to Mount. Ready to Wire. Built for Active Systems. The M10D-S GUS ships fully prepped. The Proline X terminal cup is installed and pre-wired with 12-gauge OFC to both driver positions — connect your amplifier run and wiring is complete. Both baffles use 8/32 threaded inserts with stainless machine screws included. Polyfill is factory-installed in both chambers independently. Rubber feet for downfiring are included. Plan Your Wiring Before Selecting the Voice Coil Variant The GUS-10 is a dual voice coil driver — available in Dual 2Ω (D2) and Dual 4Ω (D4). With two drivers the wiring combinations produce multiple final impedance options. The recommended configuration for most builds is two D2 drivers, each wired series (4Ω per driver), then both in parallel (2Ω final). See the wiring chart above and confirm your amplifier's stable impedance before ordering. D2 T/S parameters are not yet finalized by ResoNix — D4 data is published and is the basis for this enclosure's volume calculation. Where It Fits At 34" × 14.75" × 8.25", the M10D-S GUS is wider and deeper than the single GUS-10 enclosure but remains significantly more compact than any conventional dual 10" sealed build. Measure carefully before ordering: Trunk floor — full-size sedans and sport sedans Cargo floor — mid-size and full-size SUVs Behind-seat — full-size crew cab trucks Dual front sub builds — DSP-controlled SQ systems SQ competition — maximum GUS-10 output at minimal depth High-output shallow installs — where two 10s replace one 12 2-Year Warranty All Proline X Micro Series enclosures carry a two-year manufacturer's warranty against defects in materials and workmanship. Built and inspected in our Tullahoma, Tennessee facility before shipment. Contact Audio Intensity directly for warranty support. Made in Tennessee Every Proline X Micro Series enclosure is CNC-cut and hand-assembled in Tullahoma, Tennessee on ShopSabre CNC routers. Chamber volume, divider placement, cutout geometry, dado joint depth, baffle layer count, dowel placement, and terminal positioning are all held to spec on every unit. Langboard Elite MDF throughout — named, mill-documented, published density and bond specifications.