Starlink Mini Wireless Remote Switch — Inline Plug and Play

Starlink Mini Wireless Remote Switch — Inline Plug and Play Switch your Starlink Mini on and off from inside the cab, the camper, or your camp chair. Plugs straight into your existing DC line — zero wiring, paired out of the box. This inline wireless remote switch sits between your power supply and your Starlink Mini's DC cable. Plug the male end into your power source, plug your Starlink cable into the female end, and you have full remote on/off control of your dish — no more crawling to the socket, unplugging connectors, or leaving the Mini running all night to avoid the hassle. ⚡ Key Features 🔌 True Plug and Play No wiring, no relays, no installation. It goes inline on the DC cable you already use — plug in, press the remote, done. (Prefer a permanently wired setup? That's our wired Wireless Remote Control Switch — see the comparison below.) 🎛️ Two Pre-Paired Remotes Included Both remotes work out of the box — no pairing procedure, no learning buttons. Keep one in the cab and one in the van, or a spare in the glovebox. 🔋 Stop Idle Power Drain The Starlink Mini keeps drawing power whenever it's plugged in. Switching it off remotely when you're not using it protects your battery overnight — flick it back on in the morning without leaving bed. 🌧️ Weatherproof DC Connectors Sealed barrel connectors matched to the Starlink cable spec, suitable for outdoor runs to the dish. ➡️ Simple Directional Setup Male end = input from your power supply. Female end = output to your Starlink cable. That's the whole install. 📋 Specifications Remotes: 2, pre-paired | Wireless: 433MHz RF | Input: DC Male | Output: DC Female | Connectors: Weatherproof barrel (Starlink cable spec) | Install: Inline, no wiring | Weight: 60g with both remotes | Designed for the Starlink Mini DC power line 🤔 Inline Remote vs Wired Remote Kit — Which One? The Inline Plug and Play (this product) is for anyone running the standard Starlink DC line — OEM supply or one of our step-up converters — who wants remote control with zero installation. The wired Wireless Remote Control Switch ($29.95) is a 30A relay kit that wires into any 12V circuit — the better pick for permanent installs, custom switchboards, or switching other gear alongside Starlink. Common Questions Q: Where does it go in my setup? A: Inline on the DC run between your power supply and the dish. Plug your supply into the switch's male end, then plug your Starlink cable into the switch's female end. It is directional — if it's connected backwards the unit will power the dish but the remote won't switch it off, so if that happens just flip it around. Q: Do I need to pair the remotes? A: No. Both remotes come pre-paired and work straight out of the box. Press once for on, press again for off. Q: Will it work with the step-up converters? A: Yes — it's designed to sit on the dish side of your power setup, after the OEM supply or a step-up converter. Pair it with our step-up converters for a fully remote-controlled 12V setup. Q: Why switch the Mini off at all? A: The Mini draws power the whole time it's connected — typically 16-20W, more in poor weather. Left on overnight that's a meaningful drain on an auxiliary battery. A remote switch means you actually turn it off, because turning it back on is effortless. Q: How is this different from your wired remote switch? A: The wired kit is a 30A relay you install into a circuit — more powerful and more flexible, but it's an installation job. This inline version needs no tools and no wiring: it only takes over the Starlink DC line itself. Same convenience, two different installs. Both use 433MHz RF remotes. Whether you're working the paddock, set up at camp, or running a remote site — control your Starlink Mini without leaving your seat. ✅ In stock – ships fast Australia-wide 💨 Express shipping options available Not sure which cable you need? Check out our Cable Selection Guide or download the Quick Reference PDF.