Chicago Pneumatic CPRS 3-270 Silent Air Compressor (270L)

If noise is the reason you have been putting off a proper workshop compressor, the Chicago Pneumatic CPRS 3-270 solves it. At 65+ dB(A) it runs at roughly conversation level, so you can work with customers on site. Unlike smaller oil-free units, you are not trading capability for quiet: this is a full two-stage machine on a 270 litre receiver. SilentTwo-stageMade in Italy240V 15 Amp65+ dB(A) at 4mSuper duty PowerNeeds a 15 Amp breaker, not a standard household point. Check before ordering. WorkloadTwo-stage pump and 270L reserve built for continuous professional use all day. Noise65+ dB(A) at four metres, roughly conversation level. The quietest capable unit in our range. Air qualityOil-lubricated. Fit a filter and water separator before any tool used near paint or interiors. Best suited to Ideal for Detailing studios with customers on site Workshops in residential or shared buildings Ceramic coating and PPF studios Single-bay professional setups running air daily Anyone who has had noise complaints Not the right choice if You only have a 10 Amp power point You need to move the compressor regularly, it weighs 175 kg You need three or more tools running at once Space is tight, it is over 1.5 metres long What it can handle Application Suitability Blow gun / drying Comfortable Interior cleaning gun Comfortable, the 270L reserve absorbs demand easily Tyre inflation Comfortable Air sander or polisher Suitable for single-operator use Spray gun, touch-up work Suitable with proper filtration fitted Two tools at once Possible for low-draw combinations, not recommended routinely Three or more tools Not suitable, look at the three-phase range Tool and application suitability above is general guidance based on typical air consumption, not a performance guarantee. Actual results depend on your tools, air line setup, working pressure and how continuously you run them. If you are unsure whether this compressor suits your specific setup, get in touch before ordering. Before you order: Requires a 15 Amp breaker. At 175 kg this is a fixed installation, plan its position before delivery. The airflow figure below is piston displacement, not usable output. Specifications Specification Detail Motor 3 HP / 2.2 kW Piston displacement 13.8 CFM / 391 L/minWhat the pump moves. Usable output is lower. Maximum pressure 10 bar / 145 psiMost detailing tools run at 6 to 8 bar. Minimum operating pressure 6 bar / 87 psi Air receiver 270 litres, AS1210 certifiedOver five times a typical 50L garage compressor. Power supply 240V single phase, 15 Amp breakerNot a standard household outlet. Noise level 65+ dB(A) at 4 metresRoughly normal conversation level. Pump speed 1100 RPM Compression Two stageRuns cooler and more efficiently under sustained load. Air discharge 1/2 inch BSP Construction Cast iron barrels, aluminium heads Weight 175 kgA fixed installation. Dimensions (L x W x H) 1522 x 580 x 1242 mm Country of manufacture Italy Warranty 1 year Choosing the right option Choose this if noise is a genuine constraint and you need professional capability on single-phase power. Step down if noise is not an issue. The CPRC 3-100 has the same 3 HP motor at a fraction of the price, simply louder. Step up if you need two or more operators on air at once. The Ironman 5-150 delivers 17.9 CFM usable output, though it requires three-phase. Common questions Can I plug this into a normal power point?No. It requires a 15 Amp circuit, which uses a physically larger plug. This is the most common reason a compressor cannot be commissioned on delivery, so check first.How quiet is 65 dB(A) really?Roughly normal conversation level at four metres. A standard workshop compressor typically runs 10 to 15 dB higher, which is a substantial difference in perceived loudness.Will it run an interior cleaning gun continuously?Yes. These typically draw 5 to 7 CFM, and the 270 litre reserve provides a substantial buffer so the motor is not constantly cycling.Do I need a filter or dryer?For blow guns, a basic water separator is enough. For paint, coatings or PPF work, fit a proper filter and water separator. This applies to any oil-lubricated compressor.Can I move it myself?At 175 kg and over 1.5 metres long, no. Plan its position before delivery and arrange appropriate handling. Planning a full compressed air setup? Plan Your Air Line Compare All Compressors