Aluminum RV Sewer Hose Storage Carrier, Camper Hose Tube Support Accessories

Aluminum RV Sewer Hose Storage Carrier for I-Beam Frames Quick answer: This adjustable aluminum carrier stores a compatible RV sewer hose outside the RV. It mounts to compatible exposed I-beam frames, adjusts from 54.5 to 95 inches, and has a listed 4.7-inch inner diameter. Key Product Facts Primary use Under-RV storage for a compatible sewer hose Frame compatibility Compatible exposed RV I-beam frames; measure and inspect the mounting area before ordering Adjustable carrier length 54.5–95 in Listed inner diameter 4.7 in Listed hose fit Most standard 3-inch RV sewer hoses and many removable fittings Known fit limitation Not intended for large one-piece 90-degree sewer fittings Main material Aluminum tube and aluminum end caps Mounting method Bolt-through brackets with bolts and lock nuts Listed bracket clearance Approximately 1 in; does not guarantee clearance on a specific RV Listed item weight 13.17 lb Listed package dimensions 56.5 × 7.25 × 6.5 in Why Choose the Safoner Carrier? Aluminum tube and end caps: The aluminum tube and end caps form the main carrier structure. Easy-open hinged end caps: The door-style cap stays attached and opens without being unscrewed. Easier hose access: The split-bracket layout allows the opening position to be selected around a compatible installation area. Reinforced adjustable joint: Three connection plates and two stainless steel locking clamps secure the telescoping overlap. Bolt-through mounting: Bolts and lock nuts secure the upper and lower brackets to a compatible exposed I-beam mounting area. Store the Sewer Hose Outside the RV The carrier keeps a compatible sewer hose in a dedicated under-RV storage location instead of inside a clean storage compartment. The telescoping inner and outer aluminum tubes let you adjust the installed length to suit a compatible mounting span. Easier Sewer Hose Access with a Split-Bracket Layout The split-bracket design gives the installer flexibility to position the carrier opening closer to an accessible RV side when the frame and nearby components allow it. Select the position carefully so the end cap can open fully without contacting the frame, suspension, plumbing, wiring or other equipment. Easy-Open Hinged Aluminum End Caps The aluminum end caps use a door-style hinged design and remain attached during normal opening. Built-in vent holes promote airflow inside the tube, while the safety cables and carabiner clips provide secondary retention. Because the caps are vented, the carrier is not sealed or watertight. Reinforced Telescoping Connection Three connection plates reinforce the overlap between the inner and outer tubes. Two stainless steel locking clamps secure the plates after the carrier has been adjusted to the required length, helping reduce movement and sagging at the adjustable joint. Secure Bolt-Through I-Beam Mounting The upper and lower brackets use bolts and lock nuts for a bolt-through connection at compatible exposed I-beam mounting locations. This product is not designed to rely on self-tapping screws alone. Installation requirements vary by RV, so confirm drilling access and the condition of the mounting surface before installation. Approximately 1 Inch of Bracket Clearance The bracket shape provides approximately 1 inch of listed clearance below the I-beam. This can provide more room around nearby wiring and lines, but it does not guarantee fit or safe clearance on every RV. Installation warning: Inspect both sides of every drilling and fastening location. Do not drill into or pinch electrical wiring, plumbing, brake lines, tanks, enclosed frame sections or other hidden components. What Is Included 1 adjustable RV sewer hose storage carrier assembly 3 connection plates 2 stainless steel locking clamps 2 upper mounting brackets and 2 lower clamp brackets 4 adhesive rubber strips 1 drill bit and 1 dual-size hex driver bit 2 cable ties 2 carabiner clips 4 short locking bolt sets and 4 long locking bolt sets Before Ordering Confirm that the RV has accessible, compatible exposed I-beam mounting locations. Measure the required span and confirm that it falls within 54.5–95 inches. Confirm that a 4.7-inch inner diameter fits the hose and removable fittings you plan to store. Check clearance for the split brackets, full end-cap opening, wiring, plumbing, suspension, tanks and other nearby components. Confirm that both sides of each bolt-through mounting location are accessible and safe to drill. Do not order for a large one-piece 90-degree sewer fitting unless you have independently confirmed fit. Frequently Asked Questions Will it fit every RV sewer hose? No. The listed 4.7-inch inner diameter fits most standard 3-inch RV sewer hoses and many removable fittings, but it is not intended for large one-piece 90-degree fittings. Measure the largest part you plan to store. Does it fit every RV frame? No. It is designed for compatible exposed RV I-beam frames. The mounting span, flange dimensions, drilling access, bracket placement and nearby components must be checked on the specific RV. Can the opening be positioned closer to the RV side? The split-bracket layout allows flexible positioning within a compatible mounting area. Final placement depends on the I-beam, available drilling locations, end-cap swing and clearance from nearby components. Are the end caps removable? The end caps use a hinged door-style design and remain attached during normal opening. There is no separate threaded cap to remove and store. Is the carrier waterproof? No. The end caps include vent holes for airflow, so the carrier should not be treated as sealed or waterproof storage.