TURNKEY 2018 RH RACE CARS PRO MOD CAMARO

Up for sale is a turnkey 2018 Camaro Pro Mod, professionally built by RH Race Cars and powered by a PLR MH5 564ci Hemi with a Harts Charger. This Camaro is a race-ready, professionally built combination with quality parts throughout. The car has 150 runs since new and only 4 runs on the engine since freshened. It has been a proven performer with a best 1/8-mile ET of 3.59 at 212 mph. This would be a strong fit for all forms of Pro Mod, like PDRA Pro Boost or even RVW. Engine: Engine Type: PLR AJPE Hemi MH5 outlaw Cubic Inches: 564 Bore Space: 4.8" Block: AJPE Crankshaft: Callies (10 runs) Connecting Rods: R&R 12mm (4 runs) Pistons: Diamond (4 runs) Wrist Pins: Trend (4 runs) Piston Rings: Total Seal (4 runs) Oil Pan: Moroso Wet Sump with Taylor Blanket Oil Pump: System 1 Camshaft: Militia PLR Grind Lifters: Jesel .937 Keyway Pushrods: Smith Bros Rockers: Reid Cylinder Heads: AJPE MH5 Outlaw Valves: Xceldyne Valve Springs: PSI Valve Covers: PLR Billet Intake Manifold: Frankenstein Balancer: ATI Chassis & Body: Year Built: 2018 Model: Camaro Body Construction: Carbon Fiber Chassis Serial Number: RH Race Cars 0073 April 2018 Chassis Certification / Expiration: SFI 25.3 Base Weight: 2400 lbs, no driver or ballast, 50 lbs Removable Ballast Included Wheelbase: 112" driver / 110" passenger (2" stagger) Midplate to Axle Centerline: 82" Bottom of Steering Wheel to Floor: 17.5" Seat to Bottom of Steering Wheel: 20" Seat to Pedals: 40" Bottom of Seat to Roof Bar: 38" Door X to Double Frame Rail: 22" Center of Door X to Roof Bar: 22.5" Front Suspension: Menscer with Air Rear Suspension: Menscer without Air Front Brakes: Strange Carbon Rear Brakes: Strange Carbon Front Wheels: Weld (New) Rear Wheels: Weld Double Beadlock 18" Rear End: 10" Strange Modular Driveshaft: PST Carbon Third Member: 10" Mark Williams 4.57 (8 runs) Wheelie Bars: MVM Double Carbon Fuel Cell: ProCharger Style Parachutes: Simpson Fire System: Safecraft Seat & Harness: Racetech impacts belts Headers: Zoomies (New) Paint: Wrap Drivetrain & Electronics: Power Adder: Harts Charger 140 (10 runs) with Stroud Blanket Transmission: M&M 3-Spd (21 runs) Torque Converter: M&M Engine Management: FuelTech FT 600 Fuel Injectors: FT Injectors 720lb/hr x 8 / Billet Atomizers 700 hr/lb x 8 Fuel Pump: Aeromotive Ignition: FT Spark-8 Wiring: FuelTech Harness Pro Wire Battery: Lithium Pros with Charger Parts available for additional cost: Complete Spare Engine Pro Jacks ProFab Trans Cooler Spare Weld 18" Rear Wheels and Tires Spare Zoomies 8 x Spare FT Injectors 720 lb/hr 8 x Spare Billet Atomizers 700 hr/lb Carmack Third member Electrimotion Shut off system 3 x New FuelTech CDI coils 8 x Used FuelTech CDI coils (Tested by FT USA) Used FuelTech Spark Pro 8 (Tested by FT USA) 2 sets of Victory retainers 3 x New TurboSmart blow-off valves 14 x Trend spare wrist pins and buttons 3 x Spare exhaust rockers 2 x Spare intake rockers 2 sets of Jesel lifters (Rebuilt) 10 x Used Victory1 intake valves 2 x MSD 2348 Hall Effect sensors Meziere starter 2 x Spare axles 20 x MH5 pushrods, 11.300" 21 x MH5 pushrods, 12.060" 4 x Darton sleeves 8 x MH5 Trick Titanium Intake valves 8 x MH5 Trick Titanium Exhaust valves 10 x New MH5 exhaust valves 8 x Used Victory exhaust valves 3 x Stators RCD crank hub RCD trigger wheel Please reach out to Eric at 770-231-2993 or contact us with questions.