Bed fly rewrite

If you're still using guy ropes and pegs to set up your Jayco camper trailer bed end flies, this kit eliminates the need for them on most trips. The CaravanMods Bed Fly Conversion Kit converts your existing bed flies into a freestanding structure, removing your reliance on ropes and pegs and the tripping hazards that come with them. It fits the Jayco Swan, Lark, Hawk, Eagle, Flamingo and most other Australian wind-up camper trailers. Setup goes from a two-person job with ropes to a solo task in minutes. Most of our customers call it the single best modification they've made to their camper. Find the right kit for your trailer Answer a few questions — we'll tell you exactly what to order ↺ Start again 1 Your poles 2 Pole modification 3 Trailer year ✓ Your kit Not sure which kit you need? Answer 3 quick questions and we'll tell you exactly which option and mounting kit is right for your trailer — no guessing required. Start here → Takes about 30 seconds ✓ Q1 — Your poles: Edit Question 1 Do you have the following existing bed fly poles? Pole requirements You must have all of the following: 6 x upright poles (Pole A) 2 x roof rafter pole (Pole B) 1 x roof rafter bracket on the trailer at each end Poles must be 25mm OD at the thick end and 22mm OD at the thin end ↕ Tap to enlarge ✓ Yes — I have all of these ✕ No — Missing or not sure ✓ Q2 — Pole modification: Edit Question 2 How would you like to handle your existing poles? This determines which option is right for you. Option A — Cut them Yes, happy to cut them up — I understand they can't be restored afterwards Option B — Disassemble only Happy to disassemble them but keep them intact — reversible, good for resale Option C — Keep factory poles I don't want to change or modify the factory poles at all ✓ Q3 — Trailer year: Edit Question 3 What year is your camper trailer? Check the compliance plate on your drawbar or A-frame if unsure. Pre-2019 2019 2020 or newer Not sure Your recommendation This combination is currently out of stock. Contact us and we'll let you know when it's available. Checking availability… ↺ Start again ✕ On this page Which configuration? Step 1 — Choose option Step 2 — Mounting kit Comparison table What's included Important notes FAQ Installation manuals Which configuration do I need? When buying you'll have two decisions to make — which option and which mounting kit. The right combination depends on: How much modification you are willing to do — review Step 1 The poles you already have — review Step 1 What mounting options are compatible with your trailer — review Step 2 There are 3 option types and 3 mounting kit types. Step 1 — Choose your option Choose Option A, B or C first. A Option A Traditional Conversion Kit Best suits: If you already have compatible poles and are confident in DIY to cut and crimp the plastic inserts into place per the instructions (allow 1-2 hours). What we supply: We will supply a bag of loose plastic inserts and the correct mounting hardware. Uses your existing poles. Requires cutting / removal of existing fittings New fittings inserted and secured into poles Lowest-cost option if poles are compatible Note: The above image shows contents for Option A, Mounting Kit 1 Pole requirements You must have: 6 x upright poles (Pole A) 2 x roof rafter pole (Pole B) 1 x roof rafter bracket on the trailer at each end The above poles must be 25mm OD at the thick end and 22mm OD at the thin end B Option B Hot Swap Pole Kit Best suits: If you have compatible poles but do not want to cut them. A very easy option with very little DIY skill required. (30 min install) What we supply: We will supply some complete poles and some half poles which assemble easily with your existing poles to get the full required pole configuration You simply telescope apart your existing upright poles. To then assemble the end with a spike into our supplied half poles. No cutting required, reversible if you wish. Great for resale value giving the new owner the factory option if they want it and also the improved bed fly conversion kit. Note:The above image shows contents for Option B, Mounting Kit 1 Pole requirements The pole requirements for Option B are the same as option A. Just an easier installation process. Please review Pole A's pole requirements Most popular C Option C Complete Pole Kit Best suits: If you don't have the right poles, are missing poles, or just want everything supplied to in finished! Allow 10 mins for once off install What we supply: Everything you need, no reliance on you to have or modify any of your existing poles! Complete pole kit included Simplest option when pole compatibility is uncertain or if you just want a factory finished high quality solution. Note: The above image shows contents for Option C, Mounting Kit 1 ✓ No pole requirements Everything is supplied — no existing poles needed. Quick decision guide All options finish at the same end solution, the difference is that some take more DIY effort and because of that they are more affordable to buy! On the other hand, the more expensive options are supplied ready to go! Choose Option A if: Your poles are compatible You're happy to modify them (~2-3hrs work, once off) You want the most economical solution Choose Option B if: Your poles are compatible You do not want to cut them You want flexibility to swap back Choose Option C if: Your poles are missing Your poles are non-standard Your poles are not compatible You want a complete new kit, factory finished Step 2 — Choose your mounting kit After choosing Option A, B or C, choose Mounting Kit 1, 2 or 3. The mounting kit determines how and where the angled upright poles attach to the camper trailer. There are two mounting styles: Bolts Mounting and Bird Beak Plate Mounting, combined into 3 kit choices. Depending on the mounting kit you choose will define what ends we supply to you in Option A, or what pole types we supply to you in Option B or C. e.g. Any bolts mounting will be accompanied by bow end insert poles to suit the bolts mount. Likewise any bird beak plate mounting will be accompanied by bird beak peg polls Most Universal & most popular 1 Mounting Kit 1 Bolts front and back Universal and most recommended all camper trailers. ✓ Universally suits all outback, touring & bushpack models ✓All hardware provided ·✓ Most secure mounting style in high winds (The bolts act as a secure pin joint NOT a clip like the bird beaks) ✓Easiest to install on side rails underneath the main body iThis option also keeps all uprights consistent at both ends — no need to sort front and back poles when packing up or setting up. 2 Mounting Kit 2 Bird beak plates front and back Very rarely needed — only for 2019 Outback model or custom installs. ✓Bird beak plates at both ends (4 in total) iRequires a flat mounting surface iScrews not included — depend on mounting surface 3 Mounting Kit 3 Hybrid: Bolts one end, bird beak plates one end Hybrid approach for specific trailer configurations. iMixed Mounting - Bolts one end and bird beak plates the other. iBolts mounting hardware and 2 x Bird beaks supplied ! Screws for bird beak plates not included i2 Diagonal uprights with Bird Beak pegs and plates General guidance: Mounting Kit 1 is the most universal, it will suit all touring models, outback models and bush pack models. You may find some photos online of old outback models using bird beak plates on the rear bumper bar. We no longer recommended this because the poles sit too narrow and scrape on the slide out beds. However, The bolts mounting allows the poles to sit slightly wider once set up and means the poles are well clear of the sliding beds. Option comparison table Option Uses existing poles Pole cutting required Best for Option A Yes Yes Compatible poles, happy to modify Option B Yes No Compatible poles, want reversible setup Option C No No Missing, incompatible or non-standard poles What's included Each option is available in Mounting Kit 1, 2 or 3 — inclusions vary depending on the combination selected. A Option A + 1 Mounting Kit 1 8 x Bow end inserts (SKU: 401) 2 x Clips (SKU: 400) 2 x Hardware Kits for Bolts Mounting (SKU: BFCKHW02) A Option A + 2 Mounting Kit 2 4 x Bow end inserts (SKU: 401) 4 x Bird Beak Pegs (SKU: 406) 4 x Bird Beak Plates (SKU: 405) 2 x Clips (SKU: 400) A Option A + 3 Mounting Kit 3 6 x Bow end inserts (SKU: 401) 2 x Bird Beak Pegs (SKU: 406) 2 x Bird Beak Plates (SKU: 405) 2 x Clips (SKU: 400) 1 x Hardware Kit for Bolts Mounting (SKU: BFCKHW02) Note: all inserts are designed to fit into both 22mm and 25mm ends of a pole given their dual diameter stem design. B Option B + 1 Mounting Kit 1 4 x Bow end insert outer pole (you supply the inner from your existing uprights) 2 x Spreader bar with bow end inserts fitted on both ends 2 x 150mm Spigot to C clip Pole 2 x Hardware Kits for Bolts Mounting (SKU: BFCKHW02) B Option B + 2 Mounting Kit 2 2 x Bird beak peg insert outer pole (you supply the inner from your existing uprights) 2 x Bow end insert outer pole (you supply the inner from your existing uprights) 2 x Spreader bar with bow end inserts fitted on both ends 2 x 150mm Spigot to C clip Pole 4 x Bird Beak Plates B Option B + 3 Mounting Kit 3 4 x Bird beak peg insert outer pole (you supply the inner from your existing uprights) 2 x Spreader bar with bow end inserts fitted on both ends 2 x 150mm Spigot to C clip Pole 2 x Bird Beak Plates 1 x Hardware Kits for Bolts Mounting (SKU: BFCKHW02) C Option C + 1 Mounting Kit 1 8 x Bow end inserts (SKU: 401) 2 x Clips (SKU: 400) 2 x Hardware Kits for Bolts Mounting (SKU: BFCKHW02) C Option C + 2 Mounting Kit 2 8 x Bow end inserts (SKU: 401) 2 x Clips (SKU: 400) 2 x Hardware Kits for Bolts Mounting (SKU: BFCKHW02) C Option C + 3 Mounting Kit 3 8 x Bow end inserts (SKU: 401) 2 x Clips (SKU: 400) 2 x Hardware Kits for Bolts Mounting (SKU: BFCKHW02) Important notes before buying ⚠ The bed fly is not included. This is a pole conversion kit only. The bed fly pictured is not included unless explicitly stated otherwise. Wind and tie-down advice A freestanding setup reduces the need for guy ropes and pegs, but it is not a licence to leave the bed flies unsecured in strong wind. In normal conditions the setup is typically adequate as installed. In strong winds, use additional tie-downs such as octopus / occy straps — hook them through the lower eyelets on the mesh and loop around the bed support poles. If the bed fly conversion kit is set up with the poles extended such that the bed fly material is taut this will put tension in the bed fly material making it difficult for the structure to fail in wind. Toolboxes and stone shields In most cases a front toolbox or stone shield does not prevent the kit from working. To check: Set up your bed fly using the traditional upright poles Take one of the corner uprights Bring its foot back to where you plan to mount the bolts This shows the path the diagonal upright pole will take in the converted setup. And you can now confirm if it clashes with the toolbox, stone shield or other hardware you have fitted. Frequently asked questions What does the bed fly conversion kit do? It converts your existing Jayco camper trailer bed fly into a freestanding structure, reducing setup time and reducing reliance on guy ropes and pegs. Does the kit include the bed fly? No. This is a pole conversion kit only. The bed fly itself is not included. Which option is best if I do not want to cut my poles? Option B is the best choice if your existing poles are compatible and you do not want to cut them. Which option is best if I do not have the correct poles? Option C is the best choice if your poles are missing, non-standard, or incompatible. Which mounting kit should I choose? For most customers, Mounting Kit 1 is the easiest choice. Some Outback / off-road models may suit Mounting Kit 3. If unsure, send photos of your trailer's mounting areas. Will this fit my Jayco camper trailer? These kits suit many Jayco wind-up camper trailer setups, but compatibility depends on your pole arrangement and mounting points. If unsure, contact CaravanMods with photos of your poles and trailer. What should I do in strong wind? Use extra tie-down support such as occy straps hooked through the lower eyelets on the mesh and looped around the bed support poles. Installation manuals Download the installation manual for the option you are considering: Option A manual ↓ Option B manual ↓ Option C manual ↓ Still not sure which kit you need? Send CaravanMods the following and we'll confirm the right combination before you buy: Photos of your existing poles Photos of the front and rear mounting areas Your camper trailer model if known